Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi,
I am working on nRF52840 DK for Bluetooth Locator Tag following guidelines as per Bluetooth Fast Pair: Locator tag (nordicsemi.com) . I am receiving following error...
We have developed a custom board based on the nRF52840-CKAA-R7.
Development is well into the re-release phase, and I am having some issues with battery life.
I've done...
Hi,
I have a mass storage that format a fat_fs volume and create a file when I plug the device by USB. Here is how I create a file :
It works fine, and I can see my...
Good morning,
I am developing my Zephyr solution with a Supported board RAK4631 in a RAKWireless solution called Wisblock. This is a kind of building blocks called Wisblock...
Hi,
I have the unfortunate task of needing to update a significant amount of inventory (several thousand units) using BLE OTA.
The devices are using the nRF52805 with...
Hello, I am currently developing a program that uses two SPI interfaces with the nRF5340DK. I want to use SPI3 and SPI4 for two different modules. SPI4 works fine and I can...
There are some fields that I wish to change. I am using the project direction_finding_connectionless_rx as a base to work with. I would like to be able to read and write specifically...
uart:~$ wifi_radio_ficr_prog otp_write_params 0x120 0xff63ec4f 0x9fff OTP Region is open for R/W Invalid MAC address. MAC address cannot be all 0's, broadcast or multicast...
I have a device on my desk that performs the data transfer I need, so I know it's possible. I've attached a screenshot of the successful data transfer.
I tried to replicate...
I have two toolchains and two nrf SDKs installed. v2.4.1 and v2.6.1.
I could change the toolchain used from vs code extension, but I couldn't change the west workspace....
I have been sitting with this problem for almost 2 weeks and have tried alot of different thing but without anything working,
Im using VS code with the nrf9161 and it has...
We have tried the following changes, but couldn't get expecting results.
Sometimes unable to pair two devices / Sometimes fails to link with one device
Could you answer...
I am using mbedtls to parse a certificate. The code is as follows:
It builds successfully but when I flash I get the following error:
Failed to parse certificate: -9774...
I'm trying to setup so that I can do firmware update on nRF5340 using only the internal flash. Due to the many dependencies between different images I'm creating my custom...
hi support team,
i was tesing homekit ncs2.5.3, with iphone se ios18, pairing failed, and i use another two iphone 12, they all succeed.
i can't see why the ios would...
