Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
I had an email exchange with Sebastian Brosch at Segger where he explained that SES version 5.42a is NOT a down-rev version of the IDE. In fact, it's an independent fork....
Hi!
My goal is to output a constant carrier signal on the nrf21540-DK
I've loaded the radio_test on my nrf21540-DK. The location of the test is /opt/nordic/ncs/v2.2...
Hello,
We're implementing an application that makes use of C++ std::atomic variables and their associated memory-ordering semantics for inter-processor communication between...
Hi,
I am developing on a nRF52840dk. I control a LED2 (line P0.14) with PWM in normal operation and want to leave the LED2 ON when I go to System Off mode.
I tried setting...
We have been having a persistent issue with customers that have Android phones. Our product uses the nRF SDK and we have a iPhone and Android Web app that is based on Cordova...
Hi
Is there any way to use gnss without any cloud assistance on the asset-tracker app. I set up my asset tracker app on the aws cloud and currently, I don't have a chance...
Hi there,
We have tried to implement the bluetooth uart service with the standard example project (ble_app_uart). Up to this point everything works well. But for a custom...
Hi Everyone,
I am wondering if anyone have done FFT with a nRF9160. I found discussion about FFT on nRF52, but nothing on nRF9160. Can it be done? An example would be nice...
Hi there,
I'm following the step in https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu#serial_dfu Serial DFU
Here is my code
Then...
Hi,
I am using Generic OnOff Server example and now i have added an Generic OnOff client model in same ELEMENT0 and have also added one more element ELEMENT1 with Generic...
I was trying examples direction_finding_connectionless_tx and direction_finding_connectionless_rx. Both examples use nrf52833. The log shows sync terminated Waiting for periodic...
Hello I am playing with Arduino / nrf52840 but I cannot seem to use I2S reliably.
On the first board, Seeed XIAO BLE Sense, the only pins that seem to work are 4, 5, 6....
I am looking to design a cloud connected matter Window Covering Controller device that can individually control a variable amount of matter Window Covering devices. How would...
Hello, based on the Zephyr document C++ language support : the doc mentioned that Zephyr does not support templates, so pretty much 99% of the STL are NOT available. But in...
Hi,
During the development of the firmware over nRF5340, I need to modify the ffconf.h file without changing the SDK. Based on this post I copied the FATFS files into the...
