hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hi,
When nrf9160 as serial modem, can AT command be sent/received over SPI interface without modify FW ?
As I know, the UART interface is the default setting for transmission...
Hi,
I'm trying to connect multiple device on the same peripheral (nrf5340), but my peripheral does not restart advertising once a device is connected.
How to reproduce...
Now we don't add the external capacitance and want to change the internal capacitance . I have install the test tool and send the command to write the register,but it seems...
Hi!
I have nRF5340 Devkits and already have my own PCBs with nRF5340 chips onboard. I have a task where I need to evaluate how good will be BLE signal in different locations...
I know that I can memory-map external flash using XIP in the NRF52 and NRF53. However, with XIP, you can't write to the memory-mapped addresses (makes sense since you don...
Hi,
I have written a code for the motor driver and that is going to be flashed onto nRF5340. There are two communication buses that I am using in the code: UART and GPIO...
Hello Nordic,
we want to use the nrf9160 to measure some stuff and send data to a server while being battery powered. Therefore we need the lowest power consumption possible...
hi is there any existing frameworks for the nrf52 avoiding zephyr. (eg using common native cmsis / freertos / lwip stacks)?
ideally looking for free (non keil) based SD...
Hi,
Whenever I try to run the NUS example at 115200 baudrate there is an error. Either it triggers an assert or I receive corrupted data.
What should be the ideal baud...
Hi,
Trying to understand the NFC example code in the nRF52 SDK. Just wondering why the source code is not provided for the NFC. Why is this developned in the form of static...
I'm looking into the power consumption of our code, and have reached the point where it looks like our application isn't going into sleep mode properly, and is using several...
I'm developing battery powered Zigbee End Device on SDK 4.2.0. I need to be able to receive commands from Zigbee Coordinator so I'm using SYSTEM ON sleep mode.
Right now...
Hi,
I'm using nRF9160 SLM application SDK 1.9.1
We are using the GPS in 4 operation modes and in between we sent nRF to sleep, it seems when we sent it to sleep all...
Hello,
I do not see a SWO (Single Wire Output) pin on this package. The regular size package has this function on P0.18 but not on the WLCSP package.
Please advise.
...
