Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
HI,
I start a scanning and print advertising report when address match on nrf5 SDK v16.0.0 with S140 on nrf52840. It goes well until I enable GNU extension in Keil. I don...
Hello. I have a project that needs an update.
The project was working before July 2022. However, now it doesn't work anymore (VsCode run/debug doesnt work) anymore. The...
Greetings,
during test of a device, we have tried uploading a shell sample in a nrf52840dk board. However for some reason this caused the board, or at least the installed...
Hi - I am using nRF5 SDK v17.1.0 and Segger Embedded Studio v6.34a. I am testing the ble_app_buttonless_dfu for pca10040_s132.
I am compiling ble_app_buttonless_dfu_pca10040_s132...
Dear Nordic Engineers
I would like to use the DFU trigger library to realize the NRF CONNECT for Desktop enter bootloader.
I found a demo in devzone: https://devzone...
Using a MAC running Monterey, VS code runs from command line on a terminal window from everywhere. When clicking on the "Open VS Code" button from the toolchain manager it...
For the nRF5xxxxx series, it looks like it has a differential ADC with 8 positive and 8 negative channels. It also looks like it has a scan mode where it will sequentially...
Hi,
I have a nrf9160DK and flashed it with Serial LTE Modem sample, however all the AT commands are just timing out.
Configuration is default and UART 0 is used.
...
Hi!
I want to connect my NRFL2401 to my computer using BLE (v4.0.0) in order to collect data from a sensor. However, the «Start Scan» button is not functional. When I click...
Hi!
I am trying to subscribe to nrf cloud with topic " prod/<TEAM_ID>/<DEVICE_ID>/jobs/rcv". After that I get Disconnect event in the MQTT handler.
Topic "prod/<TEAM_ID...
Hello Everyone,
I am using NRF52832 in my project and in my project I want to charge the device through USB C. So when we plug in USB C into the device, the NRF52832 should...
I followed the directions for pulling down the nRF Connect SDK v2.0.2 via Toolchain Manager v1.1.3 in nRF Connect for Desktop v3.11.1.
I am using Ubuntu 22.04.1 LTS 'Jammy...
Hi,
I am creating a central code from scratch, using zephyr version 2.0.1. I want to know the central code contain all the zephyr rtos property like thread in background...
Hi All,
I am trying to communicate with IC MAX17201 using I2C interface. I am able to detect the IC and communicate with it.
When I read 8bit registers from the IC I don...
Hello,
nRF5340, NCS2.0.2, vscode.
\v2.0.2\zephyr\samples\bluetooth\periodic_adv
when TX and RX work on PHY_1M, two side work well.
but when TX side set BT_LE_ADV_OPT_CODED...
