We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi, I am trying intialize the RTC in ncs using nrfx drivers and then connect it tick event to a saadc sampling event using a ppi channel. I learnt that RTC0 and RTC1 are used...
Hi
after create project from sample broadcast_audio_sink, when running it, i get following message:
[21:59:46:406] *** Booting Zephyr OS build v3.0.99-ncs1-2483-g482dcc7865f7...
I need to modify the code of different sensor data, which is obtained on LTE monitor, so I want that file in which I can create custom sensor data /Modify the sensor data...
Hello.
I had LC3 access granted.
I can access nrfconnect/sdk-lc3 on my web browser.
However, with bash, I get the following error and cannot build nRF5340_audio.
...
Hi Mate,
I have very small issue that is when i am trying to link config_bootloader_mcuboot=y in zephyr application the program is not flashed. I need to run zephyr application...
I was curious if there was a delta firmware update file to go from 1.3.1 to 1.3.0 on the nRF9160. Most of our business is in North America and we use a carrier who requires...
Hi all,
I'm trying to use the nrf Connect SDK and configure PWM to use in one pin from nordif nrf52DK. The final chip will be the nrf52810. I have configured the builder...
Hello,
I want to use pc-ble-driver WITH an EV-BT8400XE.
I develop with SDK15.3 (last compatible version of SDK for pc-ble-driver)
I am successfully able to use pc-ble...
Hey all together,
I'm using nrf Connect SDK 2.0.0 and want to place a variable in flash at a predefined location. The reason is, that I need to read the information stored...
Hi,
I'm setting up nRF Connect SDK according to this instruction ( http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing.html) and Getting Started...
Hey,
in our project the nrf is acting as the central and connecting phones.
As part of the connection process:
1) We check if the phone is bonded in the nrf.
2) We...
Hi,
I'm on NCS 1.8.0 and I've successfully built and run the peripheral_nfc_example sample. Printed logs when reading NDEF message using a smartphone
When I came to...
I have a nRF52840-DK that stopped programing.
As a starting point to get it back to work, I reflashed the Interface MCU Firmware.
It is correctly detected by J-Link Configurator...
Hey Nordic,
My project is based on "ble_app_uart" and "ble_app_uart_c" examples. I modified them to some extent. You can download them from here .
Normally, I can write...
Hello!
On 3 and 7 of August my employee directed to you several questions regarding NRF. Case ID: 293339
Can I at least urgently receive the answer for the question in...
