Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
hi support team,
customer is finding that 832 erase page takes more time than normal conditions, that is when the temperature is -20, erase speed is much slow.
as our...
Hi all,
I am confused about nrf52832 Tx/Rx max current. I am using PPKII measure the power current of NRF52 DK PCA10040 , As the following screen shot, :
In DC/DC mode...
Hi,
I'm working on a custom board based on PCA10100, nrf52833 but it seems to be stuck at the function "lfclk_spinwait".
my custom board does not have an external LFCLK...
Hello,
For my application I have a need to buffer data for, say, 8 GPIO pin outputs and continuously generate those buffered outputs in parallel on the GPIO pins. I have...
Hi,
According to the BLE core specification, a host can communicate with multiple controllers via HCI. I want to confirm whether zephyr's BLE stack supports the feature...
Hello,
I am working on a project using the nRF5340. I will eventually be supporting OTA DFU for both cores so I need to be able to statically define the partitions for both...
Hello, I am porting to nRF5340 from nRF52833. Previously, we were using sdk17.0.2 for nRF52833 and we were able to successfully implement encryption algorithm AES-CTR-128...
Hi,
I have a NRF52840-DK (400236). I was using it for the development. It was working perfectly.
Suddenly the issue arises the power section is heating up.
I am powering...
Hi,
I am running the standard Grove LCD code, as below but am getting an error, " Grove LCD: Device not ready.'
the code is
my overlay file is
and my proj...
Hello,
we have a set of router devices already on the market: each of them was developed using 4.0 stack.
now we're aligning the stack to the 4.2 version observing a very...
Hi!
I've followed the app timer example to implement app timers in my project. My project is low power consumption oriented. When I use a repeated timer, power consumption...
Hello,
We are integrating the nordic sdk for DFU on our own application on Android and iOS.
We need to know al the possible error codes that the sdk can sent but we...
Hi DevZone,'
I am trying to use the crypto library with CC310 backend on a FreeRTOS application using the nRF52840DK.
My problem seems to be that when initializing the...
Hello,
I am trying to set the default TX power to +8dbm for all stages of the BLE transmission process, including when advertising is active. I have referenced the "hci_pwr_ctrl...
