I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi,
The product we are developing needs to support extern Flash-based FOTA, so I downloaded the ble_extFlash sample from the following link for reference:
https://github...
PCA10121 schematic diagram U1 nRF5340 MCU is responsible for LE Audio, U11 nRF5340 interface MCU is responsible for programmer/debugger. Can you provide related software development...
I try to DFU on RaspberryPi OS by usb-serial. I put nRF52840 dongle on USB port of RPI4. And press reset button of the dongle.
I got error on nrftuil.
$ nrfutil dfu...
Hi there,
Yet again we are running into very basic issues with the nordic tools and software, and this is adding up to cost us massive amounts of time.
Within nrf connect...
I am using nRF52 DK and LIS3DH accelerometer.
LIS3DH configuration is as follows:
1. LIS3DH ODR set at 10Hz,
2. Low Power Mode (Low resolution),
3. Acceleration: 2g...
I am registering interrupts for many pins:
This only works for the first 8 pins, because from what I understand the GPIOTE peripheral is used and that has only 8 channels...
Hi
I am trying to program a nRF5340 device using programmer 3.0.0. But when I try to connect to the JTAG I get the below error.
using nRF Connect for Desktop v3.11.1 ...
Hello
SDK starts adverting when reset. I want to start adverting at the push of a button.
SDK version : 17.0.0
SWDevide : s112
When the button is pressed as above...
Hi all
I have an issue regarding central- peripheral connection.( using nRF52832)
In the past I developed a peripheral device using SDK 11.
In order to manufacture it...
Hello, I am doing a bachelor thesis using the nRF52 Development Kit to control a (RC ) car, and I am 3D-printing holders for extra peripherals. During the 3D-modeling and...
When I run nrfjprog --pinreset it says "Applying pin reset" but it has no effect on the connected nRF52832, it just continues running. Other nrfjprog operations like reading...
I am working on Apple Macbook Air with M1 silicon and I installed nRF command tools version 10.15.4macOS
When I open the toolchain manager , there is an error that shows...
Hello,
I am trying to get reliable log output using the Nordic Connect SDK (NCS) over RTT. When I use Minimal mode, the following config:
CONFIG_LOG_MODE_MINIMAL=y CONFIG_SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL...
Hello,
I am using the Zigbee NCP sample from the nrf Connect SDK and I would like to change the uart baudrate. How can I achieve this? I tried to find some configurations...
When I try to debug hci_pwr_ctrl in Zephyr/buletooth/sample using segger embedded studio, debug terminal don't have output of printk function, which based on nrf52840dk. ...
