We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I had been using the Andoid 4.24.3 version of the nRF Connect app and had no problem with performing DFUs. With the newer 4.25.1 version of the app I noticed a few things...
While trying to reply further queries, by mistake, above ticket got closed ... So, I need to discuss more to the reted issue in the ticket. When, there is a click on verify...
Hello,
I'm trying to add credential to the modem on the nrf9160. However, i keep getting a -111 error when i'm trying to connect to my server with TLS mode.
When i try...
Hi
I connected the nRF21540 to a nRF52840 like in the application notes.
Here is the schematic:
I implemented the driver and now I try to communicate over the SPI...
Hi
I'm using the PA LNA driver for the nRF21540 with the function:
void mesh_lna_setup_start(uint32_t rampup_start_capture_time, uint32_t timer_index)
Now, when I check...
Hello, the device name is being parsed ok, but the mfg data in scan response seems to be there but not sure how to print it out. Using ncs bt sample direction_finding_connectionless_rx...
Hi there,
I wanted to change the advertising name while running DFU bootloader (secure_bootloader_ble_s132_pca10040), so I basically added what I found here:
https://devzone...
Hey,
my Power Profiler Kit on a nRF52840 DK stops recording after some time with the error message " Corrupt data detected, please check connection to PPK."
The time period...
Hello! I wanted to know if there is a way where I can just send a simple string from the nrf52 to the nrf91 without using any complicated examples, I have been trying to modify...
Hi, All
Just wonder how to view the log info like below, it is used in peripheral uart example.
LOG_DBG ( "tx_done" );
which config/tool allow this please?
Thanks...
I was able to interface a 9 axis MPU9250 sensor with nRF52832 via TWI. Now I want to read more number of sensor's data i.e., I want to read 8 IMU sensors data. Since, nRF52832...
Hello there,
I'm using a nRF52840. I would like to perform a complete flash dump. I have tried using an ST Link V2 and and openOCD. It was only returning errors and the...
Hi,
Im using: nRF Connect 1.9.0, Visual Studio Code. I have: a nRF52480-dongle a nRf5340_DK
I would like to have Samples (code), to have a loop through with the highest...
i have a code base which is originally run on nrf52832 dk and i want to port it to the pca10059 dongle i run in gcc env and successfully modified the definitions and includes...
