Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have following code fragment to enter nRF52 into power-off mode. There is s132 softdevice 3.0.0 running and my SDK is 12.0.0:
int32_t ret = sd_power_system_off();
...
Hello,
I am having an issue viewing serial communication from the nRF9160 on the LTE link monitor. I am able to view output when the code is compiled from a different...
After burning the application, the following operations were performed: nrfjprog.exe -f NRF52 --rbp ALL nrfjprog.exe -f NRF52 --pinreset
There are a total of 600 devices...
Hi everyone,
I have setup a Bluetooth Mesh network of 5 Light Control Server Nodes and 5 Low Power Nodes that have friendship with eachother.
All nodes publish and subscribe...
I'm facing the requirement to save few kb of data in flash and process it over time. Because none of the standard mesh models fit, a custom mesh model will be the only option...
Hey,
I encountered a very strange problem while I was trying to connect from nRF52832 (as a central device) to my nRF52805 as a peripheral. If I am trying to connect to...
Hello,
I am working on a custom development board that is using the nRF52840. After programming the nRF52840 on the board with Soft Device s140_nrf52_7.0.1_softdevice.hex...
Hello DevZone,
A product I use uses NFC tag type 2 to communicate. It usually communicates to a separate chip but I want to replace this with the nRF52832.
I opened...
Hello,
I'm working on a product where we want the nRF52840 to be able to reset itself in hardware . This is currently done via an IO that drives a SHUTDOWN# signal into...
Hi,
I'm using TWI to control accemeter(MMA452).When I used TWI SENSOR to read my sensor, it didn't work normally.
The address of MMA8452 is 0x1C,so i want to read...
The separation of flash memory into a region for the application core and one for the network core on the nRF5340 seems rather cumbersome and error-prone.
I'm especially...
Hi,
will qmi_wwan or gobinet driver be available for nRF9160? PPPD is not available. It is quite a limitation in use to miss ethenet interface based connectivity.
Regards...
Hi everyone, I’m have a wired network of 1000 devices (relay switches) that I’ve been tasked to upgrade to wireless.
Devices are inside a warehouse, about a pallet apart...
Hello All,
I am developing product using nRF52840 Dev-kit and SDK 4.1 for zigbee and thread.
I have created the new solution using tool chain - C:\Program Files (x86)...
Hello,
I'm using the NRF52840 with the NRF5 SDK v15.3.0 and S140.
I was trying to include the nrf_fstorage library into an existing project. The problem I experienced...
