We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi, i'm developing BLE nrf52832.
Is there any way to display the remaining battery capacity on that window 10 when connecting to Bluetooth like that picture?
The remaining...
Hi,
We are programming our devices (nRF52833) in production using a Segger Flasher Portable PLUS.
We use reset after programming via SFR access.
Our devices will not...
I'm using the at cmd library ( commands like at_cmd_write_with_callback ) to communicate with the modem.
I'm trying to enable the nrf_modem library to enable OTA updates;...
Hello
in order to analyze reboot reson (HW \ SW) I use the following:
in case of kernel crash I usually get coldstack print, in this case I can analyze and understand...
Hi guys,
Based on the examples that I found in Zephyr samples documentation, I created the program where I am able to measure the voltage and temperature, and then send...
I tried running pc-ble-driver-py/advertising.py
my command was " python3 advertising.py NRF52 /dev/ttymxc4" and then I got following error
Traceback (most recent call...
Hello
nrf_drv_twi_rx and nrf_drv_twi_tx are non blocking calls?
in the SDK example, I see a while loop is used in the read call for instance which basically is blocking...
I am attempting to build a project with the command line tools as described in: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_programming.html, but it...
Dear all,
Can I achieve ble peripheral whitelist advertising without peer manager? (Assuming central address is already known)
Following are several places that I've...
I have been using the PPK II for about a month.
I just upgraded my nRFConnect to 3.7.1 and when I run the profiler, the PPK II is no longer visible (the big green window...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
Hi,
We are design custom Board using nRF52840 SOC.
We are operating it in Normal mode, using internal DCDC converter
We have used configuration 5 from reference design...
Hi, There. I am preparing to program a Mesh application based on nrf52840. The application supports the recovery from the points of power off.
So, I have a question. It...
Hi,
I'm working with the peripheral_uart example in ncs 1.6.1 and wanted to enable flow control for uart0, but do not see a way to do that.
How do I enable flow control...
Hi, There,
I develop a communication application based on a beaconing example on nRF52850 DK.
I don't know where I do wrongly. It is always stuck in the "bearer_handler_action_enqueue...
