Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello All,
I have referred the reference example code to suit my needs. Below is my code,
Code is stuck at waiting for event. Didn't get callback with oversamping of...
Excuse me:
The client made a keyboard with nrf51802.，It has been mass produced。The customer reported that the keyboard and MacBook were connected and bounding before opening...
Hi,
We have observed that in areas of poor lte connectivity, the client_inti() works well but the mqtt_connect() takes a couple of minutes and times out.
I need to change...
Hi,
I'm compiling a piece of code that uses USB CDC ACM from a .cpp file, and I stumbled on the compiler complaining about out of order initializers in app_usbd_cdc_acm_internal...
Hi,
I'm trying to use Zephyr's 'http_client' library in Asset Tracker V2. I have included 'net/http_client.h' in main.c and have set 'CONFIG_HTTP_CLIENT=y' in prj.conf....
Hi,
I want Windows PC to communicate with nRF52840 dongle over USB full speed.
Are there sample of Windows software(likes API) and nRF52840 dongle ?
I want to realize...
Hello,
What is the limitation of the total current we can source/sink at the same time in multiple pins for low Vdd?
I could find a similar question (and answer of 15mA...
Hello there, I am working on a customized nrf52832 board. For the limited size, the 32kHz crystal is not install because I think the clock from 32khz crystal can be replaced...
Hi all
I want to do a device firmware update via the bootloader, and I am unable to do so, as all attempts end with a disconnect from my Android phone (Pixel 4a). I can...
Hello!
Hardware: nrf52840 IDE: Segger Embedded Studio SDK: nrf5 SDK 17.0.2
I've been having issues with receiving USB HID IN reports on Android. If I send at an interval...
I'm trying to debug a usage fault in my NCS project using an nRF52833 DK. I can't seem to select the logging backend for coredumps. I have the following lines in my prj.conf...
Hello,
in my project i am using GSM module so i need to add UART to TEMPLATE example but i am getting error that "undefine reference to app_uart_init"
please resolve the...
Hi
The Zephyr mesh_demo project has been built correctly but I'm facing a problem when I flash it
C:\Users\OMAR\zephyrproject\zephyr\samples\bluetooth\mesh_demo> west...
Hello :)
I am using pca10056. Use SPIM to control the external flush memory of this board. I read the IC's surface, I recognized its name is MX25R6435F. (Is it correct ...
Hi. I've tried to build the TF-M Hello World sample using nRF Connect SDK and I get these two errors (which I think are related):
opening dependency file secure_fw\partitions...
