Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Which nrf5340 BLE examples build and run? I've tried several and get build errors on everything I've tried.
This is for both the app and net processor.
Hi there,
I'm using nrf52840 DK and Custom board, SDK 17.0.2, Segger Embedded Studio(SES v5.20
my problem was the code running fine but after a while it will go...
Hi,
I am using w25q16 serial flash spi memory with nrf52832.
the flash memory is working fine with all analog input pins(2,3,4,5,28,29,30,31).
but due to the hardware...
sdk version:nrf5_SDK_for_Mesh_v5.0.0_src
in example/light_switch
I use the ios nrf mesh app as a provisioner and at the network layer
I can scan and find nrf5x...
SDK 14.2, NRF52840, S140
Hi,
Thank you so much in advance for answering my very long question. I am a little confused by the low power pwm example and app_PWM documentation...
Dear Nordic Technical Support Team,
I am developing a Mesh consisting of a client requesting to a net (group) of server nodes some motion data (which triggers automatically...
hello all,
nRF Connect SDK: 1.5.0
nRF Connect Toolchain: 1.5.0
Desktop OS: Windows 10
I'm currently using nrf9160dk to explore the GNSS features. I take a look at...
Hi, I'm using the SLM application and I would like to test the PSM on the nRF9160-DK but its timers seems to be aperiodic (instead of periodic). I set it using the at command...
I want to use a UART line to send and receive data to a nrf52840 DK and then have the data sent wirelessly to a separate DK and then print it to a terminal like in the multi_sensor...
Hello,
currently am working on connecting two different modules of BLE, nrf51822 and Rn4871.
The problem am facing is that i am not able to send and receive data between...
Hi,
We are using mesh SDK 5.0 on NRF52840 integrated with PIR and light level sensors for office lighting, it works well.
Now we'd like to check if we can expand the system...
Hi while implementing/testing MTP on Linux Wireshark captured setup requests asking for "Device Qualifier Descriptor" according to section "9.6.2 Device_Qualifier" in the...
Hello,
Can you please provide information for current consumption of the GPS in these modes?
VDD=3.8V
Acquisition time = ? seconds
Acquisition current = ?mA
Tracking...
Dear all,
For our project we want to store information on the device in an additional flash partition. We have created a new flash partition, called factory_settings_partition...
