Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I'm trying to connect to a few sensors on the Nordic Thingy:52, and it fails with the following message: characteristic is not defined. The connection to the Thingy is established...
Hi,
i use nrf51822 and sdk 11.0 . I am using the ble_app_hrs_c example .This product consists of two devices，One master and one slave.
The master chip is nrf51822...
I am using the nRF52840 (with SDKv17.0.0 + s140_7.0.1) and made a custom FW based on the ble_app_hrs example. My custom HW has a 64MB S25FS512S flash memory chip.
I found...
Hi,
I am currently trying to run the DFU over UART example using my nrf52840 dk. I am using sdk v15.2.0. I followed the following instructions found in the Nordic Infocenter...
I have done a DFU code in our Customized board using NRF52832. My program was running successfully in nrf52 DK but in our customized board it's not working
While uploading...
Hi, I have a BME280 sensor running normally with the nRF9160 on v1.2.0 firmware. When I updated the firmware to 1.3.1, I had to update the code to run I updated the files...
Hi, I have a simple voltage divider circuit and I am measuring analog input from in between the resistors. I am using a custom NRF52832 being powered by a DK. I get quite...
I recently purchased a Thingy91 and have been following the start up guide but have been running into an issue with the thingy91 being recognized over USB. I was able to connect...
Hi Nordic,
I am developing a distance measurement application between the nrf52840 and nrf52833 unit for the long distance mode.
for the nrf52840 as center which running...
HI
I'm using SPI connecting to mutiple max31856(two now) on nrf52DK and SDK15.3
so I control my ss pin to pull low by myself
chip select by changing spi_pin like some...
a data array, length is 2048,use function "sd_ble_gattc_write", a error occurred, length less than 240, no error.
do {。。 err_code = write_configure(m_center_handle,14...
Hi all,
I'm using NRF SDK v17.0.2 and IEEE 802.15.4 stack library. I want to implement sleeping device. I think I should use sys_sleep_request_ms function to make the device...
Hello, Is it possible to use the USB Pins for Uart? no USB Protrocoll Would be nice if i can use the USB socket for UART with my other projects so i dont have to create a...
