Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
I've followed the instructions to apply the free Nordic license for SES but it doesn't seem to like the MAC address. You can see from the attached images that the MAC...
Hi
My device is a medical device, we are now beginning verification. One of the items on the spec requires verification that 128bit AES is used during post-bond comms with...
Hello,
I have developed a small sensor which consists of MAX30101 HR sensor and nRF52832. For the research purpose I created an app as well which shows the raw data sent...
Hi,
I am selecting a Bluetooth IC based on the availability of true randomness in it and the nRF52832 is in the list.
"The Random number generator (RNG) generates true...
Hi,
I want to run a mesh application. Can you please tell me the most preferred ide for running mesh examples.
1.segger ide
2.keil ide
Kindly tell me which one is...
Hi,
I'm evaluating the nRF52840 using the DK. I find that the hfxtal in the 52840DK is GSX-223, which is not included in the data sheets characterization of HFXTAL ramp...
Hi, I'm developing a wearable fitness device. The device collects accelerometer-gyro data and sends it to the mobile application. Initial developments are good, I created...
I'm using the <TWI Scanner> example. I use an oscilloscope to measure the signal of SCL (see image)
According to the datasheet, I'm connecting a 4.7K resistor to connect...
I am using the two units talking with each other for the BLE uart.
One is running with the example ble_app_uart_c_central. The other is running with the ble_app_uart_peripheral...
Setup:
Node: 1 nrf52840dk acting as a node flashed with mqtt_client_publisher running on top of OpenThread using the nrfSDK for Thread and Zigbee.
Debugger access via...
How are the pins of the nRF52840 used in the Nina B301 mapped into the Arduino / mbed os system? Using the pin mapping files in the ARduino code often doesn't seem to work...
Background: we have a nRF52832 based design that's been used for the past 1-2 years across a couple 100 piece batches. Our latest batch of 500 boards shows an odd behavior...
Hello all,
I'm using a nrf52840 and it's working fine. However, when I supply the chip with 5v on VDDH the GPIO output voltage is 1.8v. When I supply the chip with 3.3v...
Hi,
We are trying to use an nRF21540 FEM with nRF5340 running the latest nRF Connect SDK. Please can you advise how we can generate the necessary TX_EN/RX_EN signals to...
