We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
Recently I am using BLE for transmission on zephyr on nrf52840 When my peripheral establishes a connection with central, the subscription is also successful My peripheral...
The chip runs in the app stage and calls a function to make the chip jump to the bootloader stage (DFU mode).
The SDK we use is nrf5_ SDK_ 15.3.0_ 59ac345,
We made the...
Hello!
I have the NRF9160 DK set up to use UART2 and listen to AT commands from external MCU, NRF52840 DK configured to send using UART0.
The NRF9160 set up is done, pins...
I want to transfer 1000Bytes. if I transfer 1000bytes every second after some time connection broken,
and need to reboot the device and connect it again
how can I solve...
Hi, I get my first experiences with nRF905 modules (module DAYCOM M-FM-NR905 including spring antenna from Pollin) connected to ARDUINO DUEs. SPI communication works fine...
I'm designing a two layer board. I need to route the power supply to several parts while avoiding cutting up the ground plane. I'm consider running the power line on the opposite...
Hello
I'm trying to control the neopixeled WS2812. I referred to the following site.
https://electronut.in/nrf52-i2s-ws2812/
I'm going to use this example of neopixel...
Hi!
I'm developing serial communication programming on nRF52840 DK to get the UARTE1 communication on SDK 12.0.2.
I want to use app_uart_put or NRF_LOG_INFO function via...
I want to develop a device which can communicate with other users without any cellular coverage or network by creating a lora mesh network like above mentioned picture. in...
Hello,
I am having issues integrating mesh functionality into a preexisting BLE project.
My project is based around an nRF53832, with SoftDevice S132 and uses nRF5_SDK_17...
Hi,
i want to connect my nrf5340pdk board with the MPU6050 sensor. They should be communication using I2C.
I read different information about the connection of the sensor...
Hi,
I have two questions about the nRF52DK power consumption when powered via USB .. one is for interest, but the other one appears to be an issue.
I have run some comparative...
Hi, I found an unexpected bug which leads to stuck at this point 856419>, app_error_weak.c, 105, Mesh assert at 0x0003AA3A (:0) it's happened after a fast setting the level...
Hello,
I am trying to spot a bug in which some memory corruption is happening. I don't know in advance at which address the corruption will happen, as it happens in some...
I want to trigger SAADC samples manually, when a certain BLE message arrives. I'd ideally like to have a trigger scan 4 individual channels.
I see two function calls, though...
