Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello folks I have been struggling for some time with the driver for the MCP23S17 in Zephyr. I have already tried this code: https://devzone.nordicsemi.com/f/nordic-q-a/64024...
Hello I am developing a device that uses BLE.
User will connect bluetooth directly the first time they launch a custom app, and they will try to connect automatically the...
Hello I am using an acconeer XM122 / XB122 radar sensor with the integrated psco nrf52840, it turns out that I have mistakenly deleted the bootloader so I cannot flash with...
Dear,
I am using nRF9160 DK,
I can re-define pin for UART0 and UART1, from UART0, i can receive data from UART0/UART1.
Now, I want to send data to UART1.
Plz...
Hello,
I am using nRF51822, SDK12.3.0, pca10028, S130 as a central scanner.
Now I set the scan interval to 100ms and the scan window to 50ms. It is planned to use 50ms...
Hi,
I want to know what is the additional current or power consumption when the temp sensor is acquiring data and operating as intended.
kind regards,
Erick
Greetings,
we have a custom pcb with nrf9160 and are using nrf-sdk v1.3.0 and mfw v1.2.0
Sometimes when connecting to lte the code crashes:
The code in question is...
Hello, I am developing with: custom nRF52810 board, nRF5 SDK 17, S112.
I'm using APP_TIMER for my main tick. I have the following code I use to initialize and start the...
Hello,
I am using SDK16, Softdevice S140 with SES.
I am trying to add DFU functionality in my application and leaving only the activation of the new firmware to secure...
Hello,
I am now working on a product concept which uses RTC module to retain date and time. To speed up the development, I started with ble_sdk_app_template and I am modifying...
We're using nRF52840 with S140 SoftDevice (version 7.0.1) and 16.0.0 SDK. When USB cable is connected before USB initialization we receive correctly APP_USBD_EVT_POWER_READY...
I am very new to the Embedded world and very confused about some stuff, I have searched the internet for 8 hours and then asked here.
I am being assigned to the task of...
Hi!
I'm developing application on nrf52832 development board which will be a work indicator - for office desk ;) Main idea is that i have client based on nRF MCU and desktop...
Hi, I am searching the nRF52810 product spec and see that with standard drive, maximum GPIO output current appears to be 4mA. However, this spec is given for when the output...
