I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
We have a question regarding a custom implementation of flow control for nrf52840 using SDK16 w/ SoftDevice 7.0.1. Currently, our sensor's primary micro transfers data...
A newbie here. I am studying the simple_timer application in the nRF5_SDK_17.0.0_9d13099 library.
The sample application sets the clock frequency to the timer at 16MHz....
Looking around to develop hardware/software using the RAK4600 module!
RAK4600 (lora Node) uses Lora as its main way to communicate with my Lora server (normal flow).
Consider...
Hello,
I would like to switch on a led of a nrf52840 dongle by pressing the buton of another dongle. I don't know which example to use from SDK 17.0.2 to make a master/slave...
Pairing is rejected after setting,
i)APP_ADV_DURATION to 0
ii)adv. flag in adv. init from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE to BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE...
Hi,
I tried to implement the UART in my code, based on the UART example code. Just as in the example, I first define the struct with the pin numbers:
The pins in this...
I found there was a example in "nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10056_uart\arm5_no_packs" .
Is there a applicaion example that when it recv a specific...
Hi
I need to connect to perticular central and i know the central MAC address. So i am using whitelisting in peripheral.
I made below changes in my code in ble_app_uart...
I am trying to use the gzp_dynamic_pairing example in SDK version 16 with Segger Embedded Studio and the PCA10040 dev board. There is no project for SES so I copied what I...
Hi,
I am working on nRF5_SDK_17.0.0_9d13099\examples\peripheral\uart project.
How can I increase the UART buffer? like if I have to receive 100+ bytes data how can I read...
I am using a nRF9160 DK. I'm using a Windows 10 system and setup the SDK using nRF Connect.
I've started to experiment with the serial_lte_modem project -- version 1.3.1...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_intro.html links to two pages which cannot be found: https://infocenter.nordicsemi...
Hi,
I am able to transfer data from my custom peripheral device with nRF52840, but data is moving much slower than it should.
I am writing 244 bytes into NUS within...
Hi,
I am trying to use Cbor library provided the SDK version 1.3.0, I have added the module in my prj.conf file, however the documentation (at the top of cborencoder.c)...
