Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hello Nordic Staff,
I am using the NRF52832, SDK 15.3, Keil, and the NRF52 dk dev kits. I want to modify a program such as the UART central example to recognize my custom...
I'm measuring the current consumption of udp_with_psm program reading this post, and the current is very high. why?
https://devzone.nordicsemi.com/nordic/cellular-iot-guides...
Dear Nordic. I am working in the device that require the controller to measure its VDD line to ensure that the the device goes into sleeping mode (very low current and do...
Is there any code example for Android or iOS on how to build / send a DFU request for NRF_DFU_OP_FIRMWARE_VERSION and then how to interpret the response that comes back? ...
I want to receive data through UDP in eDRX
I tried to set up non-blocking UDP by reading this post, but I can't achieve the function yet. Any help? https://devzone.nordicsemi...
Hi all,
I am successfully using Openthread for an application on the nrf52840. As the application is growing I'm thinking about utilizing a RTOS. Therefore, I am currently...
Hello. I have integrated signature validation before boot in my boot loader. This uses the `nrf_dfu_validation_boot_validate` function, which eventually calls into `nrf_crypto_backend_secp256r1_verify...
I use the above code to copy the device root key from the flash region. The if condition at the end results to FALSE always whcih implies that the key was not copied into...
Hi,
I would like to confirm whether bootloader should start from my application with BLE buttonless DFU. Once the request to enter the bootloader is received by my app I...
Hi,
I am running the Asset Tracker application from a fresh clone of the 0.4.0 nRF connect SDK. Using the supplied iBasis SIM.
It connects after booting, and I can monitor...
Hi,
Iam using nRF52840 , And got ANT sdk from thisisant.com. Placed in the required folder & Using ANTware II v4.1. All things going well, But after programming the DK nRF52840...
Hey Nordic Community ,
I have been trying to get the Modem firmware up and running without success for a few days now (Attempted with 2 different PCs and 2 DK with same...
hi....
i am using nrf52382 .. segger 15.2version
here i have attached two programs ble_uart and twi sensor ... its working fine but data is received over ble_uart app...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use CURVE25519.
I made my code refering to example "ble_app_multirole_lesc" and "nrf_crypto_keys.h".
NRF_CRYPTO_ECC_PRIVATE_KEY_CREATE...
Hi all,
When i walk-through the battery-service provided by nRF SDK, i note the presence of " Report Reference Descriptor " in the characteristic addition function.
I...
