Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
I am trying to get the nRF52840 to interoperate with an existing product using the Telegesis ETRX357 Zigbee radio running a Zigbee 2007 PRO stack. For now, I’m using the nRF52840...
Hi,
I'm developing an application on Android based on nRF_UART apk source, but i'm having trouble in connecting to two BLE devices. Actually, i think i could manage to connect...
Hi,
I am trying to use BSP button event to take the system into sleep mode. A long push turns off IO and calls power management shutdown and the same button is configured...
Hello community!
I use the dongle PCA10059 (nrf52840) for my hardware. I already enable -DARM_MATH_CM4 and link library libarm_cortexM4lf_math.a with CMake. I can include...
Hei,
I am following the Install the toolchain section and after running
choco install python
the step does not verify because it does not find pip3.
'pip3' is not...
One of our resellers is requesting a classification code for the RF protocol. We use a Proprietary RF protocol based on ESB (Enhanced Shockburst). Is there an IEEE or a different...
I am experimenting with trying to improve the current range of gzll nRF52840 dongle to dongle (which is not that far from what I need). I am developing using nRF5_SDK_15.2...
Hi,
The top level page nRF5 SDK Documentation Library page ( https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/index ) contains a link to "S140 SoftDevice...
Hi,
I am trying to implement the DFU example from Mesh 3.1.0SDK and 15.2.0 SDK. I am following the process mentioned here .
I am using a MacOS for development.
I am...
Hi
I am using device manager and store connected devices value on next advertise device should be broadcast as bonded
static uint32_t device_manager_evt_handler(dm_handle_t...
Dear Nordic ：
Our mass-produced smart trainer( 16M external oscillator, 20PPM ) supports ANT+ FEC and ANT+ Bicycle Power , so there are two channels alive wtih 4Hz frequency...
Dear Nordic ：
Our mass-produced smart trainer( 16M external oscillator, 20PPM ) supports ANT+ FEC and ANT+ Bicycle Power , so there are two channels alive wtih 4Hz frequency...
Hi,
I used nRF52840 dongle device to run BLE multi-link Central and nrf52832 to run BLE Blinky example to test the communication of 20 nodes. How can I set and verify that...
I am making a BLE device that uses 7 ADC inputs. Most of the inputs need to read at 1hz or so. Two of these inputs are of interest
The first is a heart-rate signal that...
