We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
i have used same Serial_lte_modem sample code from nordic toolchain 2.6.0 , Enabled shell just by setting config macro
CONFIG_SHELL=y and SLM uart loging is by default...
Hello,
I'm trying to run the NVS example on the NRF9160DK rev 1.1.3 with the on-board MX25R6435F external flash memory.
The sample runs OK as nrf9160dk/nrf9160 but the...
I'm working with the Matter Template example and creating a sensor monitoring device on the nRF52840 platform, and I'm developing on a Windows environment with SDK 2.9.0....
I have a nRF9151 currently set up to observe a CoAP resource on my server. The initial GET request works, and if I respond with new updates from the server (within a few seconds...
Hi, guys. I encountered some software issues while using VS Code for development on the nRF5340 DK. During the build configuration, the code reports an error saying it cannot...
Hello, recently I bought the Seeed XIAO nrf52840 because I read in the datasheets the power consumption of the microcontroller is 400 nA typical in SYSTEM OFF mode without...
I am using VSCode with nRF extension with the latest 2.9.1 SDK.
I have been working on an application for bluetooth for the 54L15-DK.
I want to do a custom sensor driver...
Hello DevZone,
I have an nRF5340 devkit along with an nRF7002EK, and I'm looking to upgrade from SDK version 2.6.1 to 2.6.4. However, I'm facing an issue. In version 2.6...
I conducted a BLE test using two nRF52840 Dongles. Since I used Dongles, I based my code on the usbd example from the sample programs. During testing, the connection between...
Hi, I'm working on a project where we would like to track system performance using Segger Systemview. I'm building with the following RTT configs: and I'm getting the following...
NCS 2.8.0
Ble device acting as both central and peripheral.
CONFIG_BT=y CONFIG_BT_LL_SOFTDEVICE=y CONFIG_BT_DEVICE_NAME_DYNAMIC=y
#for cenral devices these are set....
I am an experienced user of the Nordic Distance Measurement Library and I am encountering an issue where the device that is assuming the role of the DM_ROLE_INITIATOR can...
Hello Nordic Team,
I'm currently integrating a watchdog on the nRF5340 CPUNET core to detect and recover from potential hangs. We’ve observed that in rare cases , the device...
Hello everyone,
I trying to configure my MDBT50Q-U512k to use the ble_app_nus example. According to my board, I need change to uart pins defined in this example. Then, I...
