Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I'm trying to reproduce the fatfs example on a nrf52840 DK and Sandisk micro SD card that's plugged into a Sparkfun Transflash breakout board. I can't seem to mount...
Hi everybody,
I'm working on a project where I want to write in an external flash nor memory, and transfer data over BLE. The combination of the peripherical_uart sample...
Hello,
I need to sample 2 saadc channels at 6Khz, and another saadc channel at approx 1/sec for a battery measurement. Which are configured for channels 0,1 and 6 respectively...
Hello all I am using nRF52832 I am using SEGGER Embedded studio for programing. I want to use pins 12 and 11 as Rx and Tx for UART. I changed the default pins to #define RX_PIN_NUMBER...
Hi,
Two weeks ago, I've tested my new devices in an anechoic chamber. I'm using Fanstel BT840X modules. These modules are using nrf52840 for MCU/Radio and SKYWORKS SKY66112...
Dear Nordic Support
I scanned through the DevZone Topics, and found a few tickets concerning MQTT-SN support.
As far as I have seen, MQTT-SN was once supported in the...
How can I enable a matter accessory device to actively send data to a matter control?
I'm using matter-lock sample to test the method of sending data from the matter-accessory...
Hello I have seen ALOT of posts referencing to first build and run ble peripheral uart example and then from there that it will be easy to remove the uart from the functionality...
Task description
I would like to use RTC2's COMPARE_0-event to trigger SAADC's conversion task via PPI, continuously. The RTC needs to operate by itself without CPU intervention...
Hello,
I'm using nRF52840 DK (Central) and nRF52840 Dongle(Peripheral). Dongle flashed with Simulation program which transmits data. DK flashed with hci uart controller...
Hi,
Are there any Thread compatible nRF chipset that are footprint pin compatible wityh nRF52832? I understand/interpret that it is not possible to Firmware upgrade 52832...
Hello,
Our customer has a project that uses nrf52833 as the master and want to connect to the slave of portable ECG meter (ble is Realtek). But they tried for a long time...
Hi,
I am currently working on SoC sensor, which is there is a process for uploading firmware from the controller to a sensor through I2C. So I am creating a function for...
Hi,
We want a solution for BLE Mesh using Coded PHY.
Normally we provision the Mesh devices using Mobile Apps.
We want Nordic module to act as Mesh provisioner to provision...
