Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi, We are evaluating whether nr54L15 supports LE Audio function? According to the specification, it supports bluetooth 6.0 and should support LE Audio (Isochronous channel...
Hi,
currently I am struggeling to get my SD card connected to the 54H20 DK. Each time I try to mount the SD Card I get the following error:
The Error is raised after the...
We are using a custom board design. I created a custom board configuration when using the v2.5 SDK. In this configuration, we have the UART0 pins configured such that RXD...
Hello,
I am using the nRF54L15-DK development kit. The peripheral-uart example works well to stream data from the kit to a smartphone using the nRF-tools App. However...
Hi
I want to use the timer in counter mode (gpio event shortcut to count task). Do you have any number of current consumption? The plan is to have a 64Hz signal but it could...
Hi, after uploading a Zephyr project (like the "Hello World" example), I couldn't see the device in the serial monitor. i add the below commend in overlay file also but still...
Hello,
I am in the process of following a series of tutorial videos on driving an LED with pwm, but I don't understand how to properly configure my .overlay file and my...
Hi,
I am developing an application for an nRF52840 using nRF Connect SDK v2.9.0. The application currently uses the Zephyr driver for simple PWM functions on several GPIOs...
Hello,
I'm using 'nRF Connect for Desktop v4.2.0' and 'nRF Connect SDK v2.3.0' on windows 11.
I was using vs code well for developing nrf52840 board.
But, I found...
Hi!
How do you recommend to debug crashes?
Especially how do you recommend to debug crashes that happen to our customers that we cannot reproduce?
So far I have been...
Hello!
I'm currently testing writing and erasing data to an external Flash using an nRF5340 and a NOR Flash, the mx25r64.
I'm going to use the SPI_FLASH example.
I bulid...
Hi,
I need to read 16-bit values from a sensor using SPI on the NRF52840. However, since the SPI peripheral only supports an 8-bit word length, what is the best way to handle...
We have nRF5340 LE Audio dks. We intend to check the PDUs transmitted. Does wireshark nrf sniffer support this if yes then how and if not then what is the possible way to...
Hello I want to operate one RGB LED SK6805-EC10-100 for that i need to write data bit by bit in between need to use some delay if any API is there please let me know.
...
