I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
Hello, when I try to send data via the UART interface using a printf statement, unfortunately this does not really work. Only one byte is sent and after that the application...
hello,
I have downloaded the DTM firmware and connected it according to the serial port pins defined in the figure below,
The selection of GPIO pins are pin 18 for RX...
I am trying to use the nRF as an intermediary bootloader for another microcontroller. All that I need the nRF to do is accept a 64kB binary file from my computer (at the moment...
Hello,
I have been testing the " ble_app_multilink_central " example given with Nordic SDK * nRF5_SDK_16.0.0_98a08e2 *.
nRF52840_DK board is working as the multilink...
I am getting an error when trying to run nrfutil, any tips on how to fix this?
~ ᐅ pip3 install --user nrfutil Requirement already satisfied: nrfutil in ./.local/lib/python3...
Hi,
I am developing project using nrf52840 and currently developing using SDK 3.0. (Once I complete my feature I will update to SDK4.1).
I am using the light bulb firmware...
Hello I am trying to run a simple zephyr bluetooth sample using nrf Connect SDK v. 1.5.1 I am using your nRF5340 DK The sample I am running is: beacon I followed your instructions...
I have one TX and another RX codes for data communication by ESB protocol. To verify whether data whitening can be enabled, I added below register setting on TX side only...
Hi. I'm developing nRF52832.
I'm in the process of setting up BLE, but there's a problem.
There was a problem while I was organizing the files due to successful BLE communication...
Hi,
I can able to get the DEVADDR0 and DEVADDR1. I am not able to make out How this EUI64 id is calculated using the DEVADDDR value.
I always get F4CE36 starting numbers...
Hi,
I'm running example mqttsn_sleepy_subscriber from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 on a nRF52840-DK with RaspPi_OT_Border_Router_Demo_v4.1.0-1.alpha.img...
Hello Nordic Team,
I am trying to flash the existing BLE light example code in nRF connect sdk to my BL653 kit with Segger Embedded Studio. The node is not getting detected...
Hi.
I'm facing an issue following this guide ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/software/posts/using-a-custom-secure-partition-manager-wtih...
I am using running "ble_app_uart_c" example in my Central nrf52 DK board and ruuning "ble_app_uart" example in my peripheral nrf52 dk board..
IF I am sending ASCII values...
