Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I am using NRF52840dk boards to make an openThread mesh network with CoAP. There is an example in NRF-SDK for coap client and another example for coap server. I used them...
I know there is an ongoing global semiconductor crisis. In the products, we decided to switch to NRF52/53 family products as core MCU. However, we're having hard time getting...
Hi,
Currently our system is using printf() to print some debug messages to the Segger debug terminal. Now we would like to reroute these messages to a UART port.
We are...
Hi there,
My nrf52840 DK seems dead. I want to recover it.
What I did:
Put the nrf52840 DK into Bootloader mode by pressing the "IF BOOT/RESET" button while powering...
Hi,
I'm working with pc-ble-driver and a PCA10040 devkit.
First, the central sends a data length update:
This returns no error (0), and on the BLE_GAP_EVT_DATA_LENGTH_UPDATE...
Hello,
we have a question about the usage of FDS. The data to save has a length of 1200 words. So the virtual page size is set to:
#define FDS_VIRTUAL_PAGE_SIZE 2048...
Hello,
I am using "pheripheral heartrate" example on SES, but I can not integrate SPI or ADC. How can I add "nrf_spi.h" and "nrf_adc.h" and relative C files on that project...
I'm using an NRF52811 and trying to configure the UARTE for Tx & Rx at 57600 baud but I'm having trouble with the Rx. I think I am dropping bytes and so want to try and exploit...
Hi,
please find attached some patches to improve the code quality of the SDK
1. Make ble_db_discovery_evt_t a const ptr
2. make p_string in ble_nus_c_string_send...
Hello,
i just loaded compilled peripheral_uart project without modification from nrfConnect sdk v1.5.1 to nrf52840 of the nrf9160 dk
and here is the output on uart output...
Hi, I successfully implemented a custom BLE service using this tutorial from Nordic. Also, thanks to a Nordic engineer, I have the QSPI example merged with the ble_app_template...
Hi,
When I open an example project in the Segger Embedded Studios I can first build without a problem. When I change the target
device under Debugger in the project options...
Hi,
I'm struggling to adjust the BLE_blinky example in the Segger Embedded Studio from the NRF52810 to the NRF52811.
I tried to follow the documentation from here (...
Shalom!
In my central nrf52840 board we connect to a TI BLE sensor that has a customer UUID base service and the TI OAD base service both with 128 UUIDs. I succeeded in...
Hi all,
In my project am sending ecg values over ble to android app. During first connection, the values are received and seems to be no problem, but when i disconnect and...
