Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hello Everyone
I have an Interrupt Signal at 8MHz after which I need to execute some stuff. I set up an Interrup on an GPIO Pin to test it but at around 4MHz the nRF5340...
I develop a pcb based on the n52832 chip, when the reference of the chip is n52832 qfaae1 all works good, but when i use the n52832 qfaab0 chip it's unprogrammable.
i'm...
Hello
I want to test the nrf52DK board by connecting it to the battery. However, the reset button does not work when only the battery is connected.
To activate the reset...
Hi,
I have three nRF52 DKs，instance is “ nrf5_SDK_for_Mesh_v4.2.0_serial”。When I send commands from PC (UART) to DKs ，DKs running well，but often no response from DK （UART...
We are going through regulation certification testing. And lab is asking what is power tolerance for BLE 1Mbps for the chip. Where can I find this value?
1.Cant make P0.09(NFC1) and P0.10(NFC2) outputs?
Tried both nRF52832 from PCA10040 and a BT module with nRF52840 and on both cant make any of those pins outputs. Tried with...
Hello
I want to test LE Coded PHY S = 2 (500 Kb / s) using the nRF5430 PDK. The SDK used is nRF Connnect SDK v1.4.0.
There is confirmation there.
1. Does nRF5430, nRF...
Hi there,
I am developing an application that uses UART. I am wondering what's the proper way to connect the nRF52840 to the PC. I researched online and found that I could...
I have a few nRF52833 development kits and want to get started with Keil (MDK-ARM). I could not find example projects in the packs that run on the PCA10100 board. Beside of...
SDK 15.3.0, code is based on examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput.
After getting the project to work with nRF Connect on the desktop...
Hi,
just start with SEGGER Embedded and use a usb acm to setup my target
to have a clean structure I moved code from main.c to dedicated files have the USB and BSP
I...
Hey all, I'm new here. So far things have been going pretty well, I am just having an issue with PPI that I can't quite figure out, but I think I'm close. I currently have...
