Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hello .
We have an issue with the SPI channel.
We found out that when our GPIO config as SPI the CS drawn a lot of current when it connect to the slave device device AD7770...
Hello,
I am working on pc-ble-driver-py to design a central (using a DevKit with a nRF52832). At this point I am trying to perform a phy update procedure but I see it is...
Hi Everyone,
I am using PSM mode in my program and want to send data everytime when modem wakes up from sleep(PSM mode). I also want to turn off/on UART only when required...
Hi,
During startup the nRF sniffer extcap script does the following:
Which (at least on Linux) breaks applications having open serial ports.
Why not instead use...
Hi all,
I have mqtt sample on my board, after I added MCUboot module from Configure nrf Connect SDK Project, when I try to debug, it gets stucked at :
#elif defined(CONFIG_ARMV7_M_ARMV8_M_MAINLINE...
hi,
nrf52840 BGA footprint P0.22 config as UART0 RX mode, don't receive any data, but config as other pin P1.06, work normally.
and I also test QFN footprint with nrf52840...
I have nrf52832 platform and my version of softDrive is (nRF5_SDK_15.3.0_59ac345). I red a lot of documents and tech support like these links but couldn't find my problem...
I have another MCU on the same board as the Nordic 52832. The firmware update image for the MCU is about 50kb in size, so instead of adding a parallel DFU for the MCU through...
So currently I am using a 5 second repeated timer to run all my operations but there is a draw back to this that the max accuracy I can achieve is of 5 sec, like if I want...
Hello!
I have 18-bit sensors with SPI and I2C , which I intend to use in a wireless array.
I need to choose equipment and topology (star, scanning mode?), enabling data...
We had a custom board made with the nrf9160 and I noticed I was having trouble communicating with the sim card on my board.
We have been testing i2c, spi, number of peripherals...
I am trying to run the hci_uart sample on my 9160 DK but I am facing problems uploading the code. I am able to run the AT client and Asset tracker just fine. As soon as I...
I've been attempting to optimize my scan and connection intervals in order to maintain the highest percentage of time scanning while maintaining connections, following the...
Hi,
I am developing a Linux PC application (central) connecting with nrf52840 dongle with s140 v7 flashed on it (for long range support). I am using pc-ble-driver v4.1.1...
Hi everybody,
I'm having a problem with the advertising function of the SoftDevice.
When the application starts advertising the function "sd_ble_gap_adv_start()" returns...
