Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi, I want to make sure that all application data are erased when we do a DFU, so that the newer application get a clean start without having to worry about data from older...
For nRF9160, is there an overview of the builtin CA certificates?
I have now deleted all certificates I added manually with:
int nrf_inbuilt_key_delete(nrf_sec_tag_t sec_tag...
We are using NRF52832 with SDK15.0 to develop a wearable device that collects data every 10 seconds. It works fine except that NRF52832 shuts down automatically 1 hour after...
Hi
My SPI Master wraps SPI comms using a couple of additional logic lines nReadFromSlave (Master Output) and nSlaveReady (Master Input).
It treats an SPI transaction as...
Hi, everybody. I have a Thread mesh network (wireless) running multiple nodes. I am using the CLI to send pings between the nodes and i analyze the mesh performance. My problem...
Hi there!
The documentation defines two possible return values for sd_rand_application_vector_get : NRF_SUCCESS and NRF_ERROR_SOC_RAND_NOT_ENOUGH_VALUES . I am wondering...
Hello,
I use ble_thread_dyn_mtd_scanner with BLE beacons but there is never any advertising received ?
If i check with my smartphone, they are detected.
Any idea please...
Hi,
How do you recommend to analyze nrf52840 dongle power consumption?
What I have is:
Nrf52840 dongle
Nrf52DK
Nrf6707 profiler kit
How can these be used together...
I am looking for a .hex file application for the nrf52840 dk that I can control from an external application via the USB port in order to setup and test the physical layer...
HI, Im developing a custom board (NRF58232) with a bmx055 connected by TWI.
I have used the twi_scanner and twi_sensor and all OK, It was working !
But now I want to use...
From what I can tell, the SDK for Thread provided from Nordic uses a precompiled Openthread library that hardcodes the UART pin configuration. This means that users of this...
I'm developing on the nRF52840, SDK15, and s140 v6.0. I'm trying to use the sd_power_gpregret_set() function to write a value that would then be read after reset to start...
Hi - I'm using a nRF52840 DK for the first time with my 2010 MacBook pro running OSX Sierra version 10.12.6. I have SEGGER Embedded Studio for ARM 4.12 installed and Segger...
I've been trying to get TWI Sensor to work on 3rd party boards for a while now and no luck.
The code I'm using is only slightly modified, (1) it explicitly defines .scl...
Hi,
I am using ppk with nrf52832 dk to measure the current consumption of my board and it giving different values at different times. for two days it gave 250uA and tested...
