I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi
currently I am working with the nRF52840 Preview DK. Using the on-board J-Link interface I can send debug messages to the debug console of the Segger Embedded Studio...
Hi,
I have tested AES-CCM of nRF52832 with reference to the following answered questions.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
devzone.nordicsemi...
Dear all,
I did below steps to connect to the BluFruit Feather board via STLink V2:
1) Install OpenOcd and STLink USB driver as: https://pcbreflux.blogspot.com/2016...
I have some code originally working using SDK 13. It reads data from the UART and send it out in scan responses. iOS was able to capture the scan response data successfully...
hi all,
Our application is a peripheral device with sensor data that is sending up to 540kb/s (68kB/s) to the central device (data rate could probably be reduced if necessary...
Hi,
I'm trying to take the readings of temperature and humidity from 4 Nordic Thingy:52 sensors by using mesh. I did the connection of the mesh and I can control the nodes...
Hello,
I am new to BLE so I am not sure where to start. I have two nRF52832 chips, one will receive data from an FPGA through SPI and then I want to send the data to the...
For reference, in case anyone else gets a similar issue :
Using the SES import facility to import a Keil MDK v5.25 Project.
After fixing a couple of other import errors...
Hi @ll,
I'm not able to receive any ble events that should be triggered by the SoftDevice.
What I did: - Using dfu_example (added beaconing advertiser and connectable...
hi,
I use SR3 52 V1.2 for development, and I want to copy a new project to change some code.
When I changed the file name, I found it could not be compiled through, only...
Hi all,
We are currently developing a wireless system for a musical instrument and MIDI controller based on a nRF52832 (using Laird BL652 modules). Our requirements prevents...
Hi,
I would like to test the ZigBee throughput like the examples ("ATT_MTU Throughput Example" for BLE and "Thread Throughput Measurement Application").
I'm not familiar...
Dear Support,
I am working with the new SDK 15, and got some question about using whitelist without device manager, and without pairing or bonding. As stated here: https...
