hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice , like this:
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I'm currently working on a project that uses the MLX90640 IR sensor. By default, this device has an I2C address of 0x33, but it can be set up with one of 127 different I2C...
Sifting through previous posts about redirecting printf to uart by using retarget.c, I have found this will work on previous versions of segger (5.42). Has anyone gotten it...
I tried adding the following settings to prj.config
CONFIG_CHIP_OTA_REQUESTOR=n
CONFIG_CHIP_QSPI_NOR=n
I've also tried to modify the Devicetree to be the qspi part in...
Hello, I have a project sampling a ADC. It has a INT output signaling new data is ready to be read with max sampling rate of 125ksps. I am using the interrupt and then reading...
Hi community,
I'm making a custom board using the NRF52840-CKAA. I'm trying to make a Bluetooth application for this board but struggle to achieve it.
setup:
- Visual...
nPM1300ek version: 0.9.0 I have both "nPM Controller" and "USB PMC" USB connected. I tried powering USB PMC through the computer and also tried a "Wall Wart USB".
I have...
Hi,
I have a device which has different UUID s for the write and read characteristics than the Nordic devices. The device I want to connect to will give out sensor data...
hi,
I am in the process of creating a board definition for a custom hardware we are proptotyping. I follwed the instructions in the intermediate course, copying the nrf5340dk...
I have a device which advertises some services, I want to discover those services and write to those characteristics. However I can only find one service and not multiple...
I'm trying to install the toolchain manager on a new work computer and I'm running into issues that I think are related to my work's proxy.
I've tried following the steps...
Hello,
I want to send audio to multiple headset(Readily avaiable from market), So is there any hardware, Software solution avaiable for that.
So, Is there any...
We've had good success measuring power consumption with the PPK2 until now. But recently, it started reporting some hard-to-explain numbers. Specifically, t told me a nRF9160...
Hello everyone,
Im currently using the Thingy:91 with the asset tracker v2 application. As I understand the default mode in this application is the passive mode. Im measuring...
Is the nRF52840-CKAA port impedance for the various transmit power settings (or at least for 8dBm) available?
Alternatively, is the expected port impedance, when viewed...
Hello,
I am building basic board on nRF5340(based on Raytac MDBT53 module) and after "Erase" operation in nRF Connect Programmer I cannot access chip anymore.
Board...