I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
We have a product which is a custom nRF52832 board, nRF5 SDK (didn't have time to upgrade to nRF Connect SDK), s132, BLE.
We used to call delete_bonds() function...
I‘m tring to run nRF5340 Audio applications with two nRF5340 Audio boards, following at: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.6.0/nrf/applications/nrf5340_audio...
I'm using the async API for UART and I have noticed that, shortly after initialisation, I receive a single character with the UART_RX_READY event. This character is 0xff ...
Dear all,
I kindly ask you what is such warning that arise in building the configuration for the NCS example, please point me to better understand why arise and the related...
I now have a 52833 board, my question is what is the difference between it and 52832?
Are they very different?
Which protocol stack does it use?
thank you
Hi
I can't find any info regarding a cut off feature for the nPM1300 if the battery voltage is to low.
we are using a battery with PMC but that is meant as last resort...
I am using nRF52840 boards. I have one query.
I understand from your documentation that MPSL schedules the Radio driver to access the Radio. And BT ticker is for time slots...
Hi
I have flashed the unit with the Vysor flash file at Vysor Dongle · koush/vysor.io Wiki · GitHub The unit is now dead and has not recovered so I am returning to amazon...
I was planning on writing firmware for the nRF52840 chip (AKA System Controller) on the NRF9160 DK. Primarily it will use BLE and serial communications over some of the pins...
Hi, I am using nRF52840 and nRF Connect SDK V2.6.0
I want to send 7000 bytes of data using USB at a time. Now I am able to send only 1024 bytes at a time. I modified USB...
I'm using the nRF52+SDK11.0.0+s132. I'm developing a system that streams BLE notifications to an Android app at ~53kbps (40B/6ms). I have the connection intervals set to 7...
Hi,
I have a system I am redesigning to use the npm1300.
It has a rechargeable battery, about 3-4 weeks per charge, connected to an nrf9160.
The current system...
Hello,
I had to build the https_client sample again to compare some behaviors on my application and as I flash it to nRF9160 I am having a cyclical error as below:
...
Hello!
We decided to switch from NCS 1.8.0 to 2.7.0 for our products and at the beggining of everything, noticed something very strange.
Prepared very simple example of...
In my application using aws_iot library, the call of aws_iot_connect occasionally results in the following error messages.
[00:00:41.412,811] <err> aws_iot: Timed out waiting...
