I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hi!
I have nRF5340 Devkits and already have my own PCBs with nRF5340 chips onboard. I have a task where I need to evaluate how good will be BLE signal in different locations...
I know that I can memory-map external flash using XIP in the NRF52 and NRF53. However, with XIP, you can't write to the memory-mapped addresses (makes sense since you don...
Hi,
I have written a code for the motor driver and that is going to be flashed onto nRF5340. There are two communication buses that I am using in the code: UART and GPIO...
Hello Nordic,
we want to use the nrf9160 to measure some stuff and send data to a server while being battery powered. Therefore we need the lowest power consumption possible...
hi is there any existing frameworks for the nrf52 avoiding zephyr. (eg using common native cmsis / freertos / lwip stacks)?
ideally looking for free (non keil) based SD...
Hi,
Whenever I try to run the NUS example at 115200 baudrate there is an error. Either it triggers an assert or I receive corrupted data.
What should be the ideal baud...
Hi,
Trying to understand the NFC example code in the nRF52 SDK. Just wondering why the source code is not provided for the NFC. Why is this developned in the form of static...
I'm looking into the power consumption of our code, and have reached the point where it looks like our application isn't going into sleep mode properly, and is using several...
I'm developing battery powered Zigbee End Device on SDK 4.2.0. I need to be able to receive commands from Zigbee Coordinator so I'm using SYSTEM ON sleep mode.
Right now...
Hi,
I'm using nRF9160 SLM application SDK 1.9.1
We are using the GPS in 4 operation modes and in between we sent nRF to sleep, it seems when we sent it to sleep all...
Hello,
I do not see a SWO (Single Wire Output) pin on this package. The regular size package has this function on P0.18 but not on the WLCSP package.
Please advise.
...
Hi,
I have several devices with the RIGADO BMDWare on them but whose hardware is inaccessible. I want to initialize these nRF52832 chips with out nRF Bootloader, Softdevice...
hi
I use nrf52840 with SDK17.1.
1.How to DFU via ble combined uart in the same application?I have sdudied a few of tickets ,example https://devzone.nordicsemi.com/f/nordic...
Hi all:
We are developing mesh project using nrf52833 based on mesh sdk 5.0. First the nrf52833 device can be sucessfully provisioned into a mesh node using mesh lpn example...
