Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi there,
There are some problems when setting nrf52840 GPIO interrupt. When I use gpio_pin_interrupt_configure_dt api to configure 11 gpio pins then download to my customer...
Hi
I am testing <InstallFolder>\examples\peripheral\usbd_cdc_acm project, when I use serial tool of pc to open port, it can send or receive data.
but if I don't want to...
I wrote this function:
When calling it and
ptr points to something odd, the chip seems to crash. Can you not dereference odd memory addresses?
Or is there a different...
Hi,
I have been using nrf5340 audio dk fir the last couple weeks with nRF Connect SDK v2.1.0 and nRF Connect SDK v2.1.1. There were issues with the audio template for walkie...
Hi,
I'm using nRF Connect 2.1.1
I create a application based on 802154_phy_test template.
When I create a configuration and build for the nRF52840 it compiles OK.
...
Hello,
I have a TMP117 attached to I2C1 on a nrf5340 and am using the zephyr NCS v2.0.0 driver to communicate with it.
How can I configure I2C1 for power management...
Hi, I am looking to use mcuboot to manage 2 separate images. The idea is that under certain conditions, image 1 would jump to image 2.
To test the idea, I am using the zephyr...
When using the Toolchain Manager through the nRF Connect for Desktop app, the Toolchain Manager is failing to fetch the index files resulting in the version 2 toolchains being...
Hi there,
as already mentioned in other tickets I'm developing a usb to uart bridge based on the nrf52820. The nRF5 SDK version I'm using is 17.1.0.
Right now I'm facing...
Hi,
When nrf9160 as serial modem, can AT command be sent/received over SPI interface without modify FW ?
As I know, the UART interface is the default setting for transmission...
Hi,
I'm trying to connect multiple device on the same peripheral (nrf5340), but my peripheral does not restart advertising once a device is connected.
How to reproduce...
Now we don't add the external capacitance and want to change the internal capacitance . I have install the test tool and send the command to write the register,but it seems...
Hi!
I have nRF5340 Devkits and already have my own PCBs with nRF5340 chips onboard. I have a task where I need to evaluate how good will be BLE signal in different locations...
I know that I can memory-map external flash using XIP in the NRF52 and NRF53. However, with XIP, you can't write to the memory-mapped addresses (makes sense since you don...
