Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello everyone,
In our custom tracking application for the nRF9160, I am connecting to nRFCloud through MQTT when needed. Either when sending a data, or requesting assistance...
Hi Nordic and everyone else!
First my question: I am sending my position data to the cloud in the same matter as the MQTT Multi Service sample. It converts some PVT data...
I have made a second rpmsg endpoint to hci_rpmsg sample and integrated direct test mode sample functionality behind that second endpoint. Application has dedicated test mode...
Hi team,
If the TTL count is 100 but the number of devices in the network is 10. Will the device routing table in BLE mesh SDK understand that the message has been already...
The UART and UARTE peripherals share the same ID (2), and only one of these can be enabled at a time.
How do you enable only one of these peripherals?
The register blocks...
I have MCUBOOT working using the default UART pin numbers. I need to change the UART RX and TX pin numbers used by MCUBOOT for a custom application. I am able to change the...
Want to store the CONFIG_BOOT_SIGNATURE_KEY_FILE in the project space, not the ncs folders.
Looking for a method to define file location without using a absolute path. ...
I am using NCS v2 and VSCode extension on Windows 11.
I have two pieces of hardware I am testing with:
Adafruit nRF52840 Feather
Custom nRF52840 board
When I flash...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I would like to automate some unit tests with NCS. I tried running the native_posix qemu builds, however, this does not support the mac m1 architecture (maybe Linux only?...
I'm updating the NCS we are using from 2.0.2 to 2.1.0 in order to use the modem firmware 1.3.3 that was just released. I verified my build with NCS 2.0.0, 2.0.1 and 2.0.2...
Hello!
I use NRF Connect SDK 1.8.0, but peripherials are configured using nrfx library.
My task is to implement serial interface where I have PIN_TX and PIN_RX. I transmit...
Hello All,
I have few questions below:
- Does the ENABLE input disconnect the internal power systems completely, or does the circuit remain in some mode and nevertheless...
Hi Sir,
I am testing the NDT w/ example "nRF_DM" (NCS 2.0.0), there are two nRF52840-DK for this test. When two boards link success, the terminal starts to show the log...
