Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi all!
I'm currently working on the UART on the nRF5340 board. The SDK describes three options: -polling API,
-interrupt-driven API,
-asynchronous API. With Polling and Asynchronous...
During development I noticed the following behavior:
If NRF_SDH_BLE_GAP_DATA_LENGTH=251 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE=185, on Android devices the connection procedure...
Hi
For some reasons my Windows 10 laptop reports two JLink CDC UART Ports when I connect one of my nRF52SDK boards.My plan is to use this board with nrf Sniffer / Wirshark...
Im struggling here with porting my code from SDK15 to NCS 2.0.2
Im happily TXing data from NRF52811 via UARTE and receiving via FTDI to PC, but Im unable to receive any...
Hello,
in the nrf connect application for mobile phone I can see the RSSI values being updated when scanning, but when I connect to my peripheral the RSSI info is not available...
Hello, I'm developing firmware for our custom board with a nRF9160.
The problem I'm having is that the modem crashes with error code 0x10 sometimes (read: about every 3rd...
HI guys I am working on nrf connect sdk v2.0.0, I am trying to modify periodic_adv example to stop changing mac address every time an advertising restart.
Hi,
I am writing the sample program "https_client" to the nRF9160-DK with Visual Studio Code's "Flash". I need to set the APN every time I write with Flash. Is it possible...
Hi,
When I'm trying to use LVGL along with Zephyr, I get the following:
I already tried to "play" with different CONFIG_MAIN_STACK_SIZE and CONFIG_IDLE_STACK_SIZE...
Hello Team Nordic,
We are using nrf9160 DK with nrf connect SDK 2.0.0 and mfw_nrf9160_1.3.2 modem firmware . In the Download_Client example we have changed the URL and the...
Based on the reference designs, the nRF52832 needs a 100pF decoupling capacitor on the DEC3 input. From my reading, this is a PSU decoupling capacitor, presumably for higher...
Our devices are provisioned via mesh shell, not over the air so we have to pass the IV index to the mesh provisioning command However, because the current IV index is not...
I was asked to create a windows application to get the device name and the signal strength of nearby modules with a nrf ble module.
The idea is to have an application the...
Hi,
I'd like to have a HW review. I have designed a PCB around the FSC-BT630 module which includes the nRF52832.
I have included all the files necessary for your to check...
