I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi:
i use nrf5340 dk;
I use Visual Studio Code IDE build zephyr\samples\bluetooth\peripheral_past simple ,but i build project in application core have a error occured;...
Hello,
I have the same issue as:
So I posted my question there but got no answer.
"it seem likes crash in "strlen()"function, and seem like "acess to illegal memory...
Hello
NCS1.9.99, nRF5340, VScode
uint8_t read[130]="";
i2c_burst_write(i2c_dev, 0x1b, 0x00, read, 128);
error:
Need to use concatenation buffer and provided...
Hi ,
I have some questions about duf Serial routine that I need your help with:
1. Can you explain the implementation process of " pb_decode,pb_encode " and the file structure...
Hello everyone,
I have a Bluetooth Mesh network of Friend nodes that communicate with eachother and allow message to pash through them.
Currently only a few need to...
Hi I am using the POWER PROFILR KIT to measure the current of the NRF5340. I combined them and set the power select and DUT select on DK and started measuring using the power...
Hello,
I am not able to connect the nrf9160 with NB-IoT to the nRF Cloud using the asset_tracker_v2 or the multicell_location sample. I added the following configuration...
Hi
I have noticed that when I configure any GPIO with "NRF_GPIO_PIN_PULLUP" option, the CPU current is raised by approximatly 200 uA. (It doesn't matter if the GPIO is...
Hello, I have managed to get two NRF5340s linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to test again. And then I also need...
Hi,
I need to enable the ADC read and GPIO pin toggling to happen simultaneously at high precision, without using the MCU resources, approximately 15 us interval. After...
We have a device that is using the nrf_drv_csense module to measure a capacitive touch via the event_handler passed to nrf_drv_csense_init(). Unfortunately, due to various...
The latest versions of MbedTLS seem to have some level of support for TLS 1.3 that the nRF Connect library's MbedTLS version lacks. How can I use a newer version of MbedTLS...
Hello,
I am trying to use Eigen matrix library in a project on the nrf52832.
I was able to compile a very simple example however I get a mem_manage_fault while debugging...
I am trying to connect a low power camera Himax HM0360 to nRF52840 dk. In the camera device specification, it is mentioned that it provides I2C serial interface and full speed...
