Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
This is the errors , please help, to successfully create .hex file
If you want to look after full log details .......
Building firmware west build --build-dir c:\Users...
I bought a thingy91 module with ibasis scheduler on board. When I made the first installation of the mfw_nrf9160_1.3.1.zip software and the thingy91_asset_tracker_v2_ltem_2022...
I'm building a simple application using I2C to read sensor data (BNO055). I confirmed I2C and my sensor are all configured appropriately and working smoothly, but when I added...
Hi,
I'm using the mqtt_simple example to develop a new application.
I want you to tell me what lines of code I need to add for the nRF9160 to work in the minimum power...
Hi,
I am working with NRF52840 DK, from this i am using KEIL IDE. I got some error while opening the KEIL SW like Cannot set path to software packs. Make sure that RTEPATH...
Hi,
My customer use nRF5340 as their master control IC, which will connect with lots of peripheral.
They are considering about simulate a uart with GPIO.
What's the...
I have designed a custom board for the nrf52840 and upon testing it in the nrf connect sdk (using a JLink), I can only see the board when it's in bootloader mode. When it...
Hi,
I am in the process of migration from SES to Visual Studio; I have imported my project; but it has no active build configuration. When I try and add a build configuration...
I am using 9160 to develop a watch product. During the network test, I found that the description of parameter period tau in CPSMS instruction and xmonitor instruction is...
So, i have created a custom board using the nrf52811 SoC. I tried to upload some bluetooth examples to it, and i can see the device on the nRF connect APP. The problem is...
On firing the following command "$ node cli create-ca-intermediate"
terminal showing error
I am following this link nordicsemiconductor.github.io/.../DeviceCredentials...
Hi support team,
I'm trying to simulate the BDM protocol of the 9s12 chip series. Basically the protocol is as follows: Communication on 1 GPIO pin, output open-drain mode...
Hi,
NCS1.9.1, VSCode, nRF5340DK cannect a NFC tag,
i write text to NFC tag by Adafruit-PN532 with anouher device,
than 5340 mcu how to read the text in NFC tag ?
...
Hi! I would to know how to partition the memory of the board and how to make that secure and trusted. Once I did that there is a way to save some information in that portion...
I'm using a nRF52832 for a product under FAA regulations. The standard requires the BLE module to perform a self-test. What self-test capabilities does the Nordic nRF52 family...
