I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
OpenThread and MCUBoot don't play well together anymore of the nRF5340 with the release 1.8 of the nRF Connect SDK. Flashing :
results in the bootloop with I assume is...
Hello,
I am a beginner in nRF. I want to implement EEPROM. So I am trying to execute Zephyr/sample/driver/EEPROM code but I am getting compilation error the below error...
Hello,
I am new to BLE. I am currently working on a beacon application. I have used the beacon example code from SDK and modified it. I am using SDK-17.1.0 controller is...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Is it possible to simultaneously send advertisements with different cycles, communication packets, etc.? If so...
I've been tinkering with my Dev Kits (3 @ nrf52840-dk and 1 @ nrf5340-dk) as I try to find the right software/hardware architecture for my use case.
I made a lot of progress...
Hello , i am developing drivers for a spi ic , which by using spi example i wrote the drivers they are working fine , also i am able to run and modify ble uart example according...
Hello Sirs
I am using the NRF3540-DK development board to program an external NRF5340 chip. I have connected the RESET,SWDCLK,SWDIO,GND,3V pins of P20 connector on development...
I need to connect a ble device to a double uart0 and Uart1 over zephyr.
The first uart in used for comunication puupose e message everty 20mS at 115200;
The second uart...
I'm trying meshdfu. Use 52832 to DFU a lantern program according to the official routine. After success, the program can run, but it can't run after DFU with 52840. Here's...
Hi,
I'm trying to build the blinky example for the nRF5340 network processor with the empty_app_core as a child image for the application processor and get a fatal error...
Hi ,
I have the nordic nRF9160 DK and the Nordic Thingy:91. I am trying with the Asset Tracking application version : nrf9160dk_fw_2021-12-15_cfedfdfa, with the last modem...
Hello !
nRF52840 have " 128-bit AES/ECB/CCM/AAR co-processor (on-the-fly packet encryption)" what is expected to be used together with RADIO for encrypt/decrypt packages...
Hi,
I noticed that latest nRF Sniffer BLE version support importing IRK, however, I can't make it successful, do you have a step-by-step guide for IRK importing on wireshark...
i just have a quick basic question about the device driver API, why does the samples/drivers/i2c_fujitsu_fram application not use a device tree node for the i2c peripheral...
