I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi to all, I'm developing a new device that should be a multiprotocol: Zigbee (as coordinator) and BLE peripheral (nus).
I use the nrf5_sdk_for_thread_and_zigbee_V4...
Hi Everyone,
I'm working on "Thread_Zigbee_v4.1.0\examples\zigbee\light_control".
I need configuration as above title.
But I relize that "zb_set_pan_id(0x1234)", "nrf_802154_short_address_set...
I am trying to use the DK Dashboard with the Serial LTE Modem Software.
The connection to the Cloud works in principle but I only can see the terminal card when connected...
Hello,
Currently I am experiencing some problem getting the NUS to send a TX notification of more than 20 bytes to the central (which is an old custom android application...
Hello,
I am offloading sockets in config. I instantiate a socket, set the send/recv timeouts, and then call connect(). It's returning a 95 which is EOPNOTSUPP. I was able...
Hi,
I'm investigating firmware image signing on the nrf9160 using MCUBoot and the nRF Connect SDK v17. I have configured
and it seems to work via `west build -b nrf9160dk_nrf9160ns...
Due to parts shortages, we are having to scramble to find compatible hardware for our project. I have sourced some nRF5340 modules but need to know if Gazell is supported...
Hi!!
I am facing an issue wherein more than one device is acquiring the leader role in a same thread network.
In my setup, I have a total of 4 devices. Three of them are...
Dear Team,
I have to use many number of pages to store data in flash memory in nrf52840 , but I am confuse that what will be start address and end address in flash_fstorage...
Hello Team,
I am facing segmentation fault while reading the OTP memory using pointer in my code. To write the OTP value I have used below command which was successful and...
Hi,
I received the nRF9160DK yesterday, and used the AT Client to get talking to the modem and connecting to a network. In VS Code I built an application from sample ...
Hi there,
I'm using the product specification of the nRF52840 to program the SAADC in continuous mode using its internal timer. I'm not able to use your SDK. Unfortunately...
We've built a custom board, at power off current is 1-2uA and when connected average current is ~4.7mA. Internal DCDC is enabled, this shaved off >2mA. Other than reducing...
Hi ALL:
- SDK version: nRFSDK 15.3
- HW: nRF52832
I am tried to earse the flash by sg_flash_page_erase(uint32_t page_number), but still failed. My code snippet as...
