Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
I'm trying to run the HID composite example on a nRF52840 dongle, and its not working:
- I refer to : nRF5_SDK_17.0.2_d674dde\examples\peripheral\usbd_hid_composite\pca10056...
Looks like 2 mistake in the latest nRF9160 production specification:
1: 1Mbps but 1200 in description section.
2: Power consumption could be in uA instead of mA.
Hello,
Sorry for the basic question, but I am trying to customize an application basing on the ble_app_cgms example.
In the debugger terminal on SES I am receiving the...
Hello,
I am currently working on an IIoT product using Zephyr and NRF SDK v1.5.1-2-g76c027893 on the NRF9160 and a WFM200 wifi chip. For this project we are using Civetweb...
Hi
I'm locking for an example like zephyr\samples\boards\nrf\system_off for nRF9160 DK
zephyr\samples\boards\nrf\system_off uses nRF51 DK or nRF52 DK board for the demo...
Dear support team,
I would like to use GPIO 09/10 as a GPIO interrupt.
I just searched and I see that need to define CONFIG_NFCT_PINS_AS_GPIOS.
But I can't do it. Please...
Hello, I'm making a system with NUS of nRF52832 and nRF52840 to sample data with SAADC. I started the system with "ble_app_uart__saadc_timer_driven__scan_mode_03" from Github...
Hello!
There is a sample simple_mqtt which is written for nrf9160 DK. Is it possible to make app_signed.hex file to load in thingy 91.
I tried to change prj.conf and have...
Hi,
Using the HRS peripheral example provided in SDK17 with S140 7.2.0, I am in the process of migrating to a custom board using nRF52833. I have already made some changes...
Hi,
Can you please tell me if Segger compiler initializes all variables to default values?
If so - can you please send me a link to that content?
Thanks
Hello,
My nRF52840 board is connected with SPI flash over SPI. I have configured the nordic as master and my SPI flash is slave as mentioned below:
Using the internal...
Hi,
I have a nRF52840 USB Dongle that I am using to perform OTA DFU to use to perform OTA DFU.
After the update is finished, the device keeps running the code instruction...
hi
I have written a driver for an SPI sensor, and it works perfect in a nrfx_spim example project.
But when I tried to add this driver to a ble custom project, errors...
I'm using the nRF5 SDK 12.3.0 on Linux (Fedora 33), with a minimal N51822 breakout board (nRF51822-QFAA(build code: H0) 256kB Flash, 16kB RAM). For programming I'm using a...
