Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
When handling a `BLE_GATTS_EVT_WRITE` from a queued write, the write event has the characteristic handle set to zero. How can I identify what characteristic is being written...
Hey there!
I'm new in the development with the nrf9160dk. And I wanted to connect the Murata SCL3300 digital inclinometer to the development kit via the SPI lines. However...
It's been a while since this Java developer really understood EE concepts.
Could someone jog my skills and explain to me roughly what the different pin rive modes are,...
Hi,
I need to send custom messages to models on my devices and I need to use a vendor model like I've seen other people on this forum use. But when I load the nRF Mesh...
Hello,
We are interfaced the nrf52811 with LSM6DSO32 through i2c and LSM6DSO32 is connected to Auxiliary(Temperature MAX30208) sensor through mode 2 connection. here I am...
I am trying to learn to use the nrfx API to control the nrf5340.
My installation is the NCS 1.6.0 with SES on OSX
It seems like nrfx most of the API devices are supported...
I'm trying to find a battery for my application and I need to know the max (peak) current draw for the nRF9160. On page 63 of the user guide, the max is 435mA with the specs...
I have a function which writes data to the external flash which is using a FAT file-system further using block device implementation of the SDK. Whenever I am calling the...
Hello,
I am working on nrf5340DK board and with a sample example "central_uart" under ncs->nrf->samples->bluetooth & "peripheral_uart" from ncs v1.5.1. I wanted to send...
Hello,
I am trying to setup test environment using nRF9160DK(PCA10090, 1.0.0)
Dev kit is located in Montreal, Canada.
I started with nRF9160_DK_Getting_Started_Guide...
I am trying to update the bootloader using BLE DFU and it does not seem like the app is launching after the bootloader update.
I currently have an app that works with the...
Hello, I am developing a Zigbee OTA client / server application. My code is based on the example from the 4.1.0 nRF5 SDK. From the example I took only the code related to...
Hi,
What is the the status of android and IOS support of bluetooth 5.0 long range ?
It would be great if you can give us a list of device that support long range (of course...
Hi,
i have some issues with nrfutil, i can't properly perform an OTA DFU over thread, either nrfutil cannot find ncp.hex or it stuck in "thread DFU server is running....
Hi,
I made a project around the peripherial-uart sample with a custom board for a nrf5340 chip.
I work with win10, Toolchain nrf Connect SDK 1.6.1
I can build it and...
