I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
Hello,
I want to to configure mesh proxy node and along with that it should also contain relay functionalities using nrf5_SDK_for_Mesh_v4.1.0_src.
Is there any sample...
I'm seeing some issues I don't understand when using RTT. Here is a short fragment of code around the RTT_Write statement.
The commented out statements are included while...
I am using nRFConnect with nRF52840 Dongle. Since the last update to SoftDeviceAPI v5, nRFConnect cannot connect anymore to this specific devices (cheap JDY-10 BT/Serial adapters...
Hi, I want to store some personal data through flash in the LPN mesh routine. I read some posts and can be implemented by using flash manager, but I can't find the relevant...
Hello, I am working on storing words to flash using fds. I am working with the nRF52 DK and SDK V15.2.0. As mentioned in my earlier post , I am storing some critical state...
Hi,
Greetings!
I am using below setup:
SDK: v16.0.0
Mesh SDK: v4.0.0
Application: Light switch server and client
Hardware: nRF52DK
Distance between client and...
Hi, I am using ble_app_uart example for peripheral device and it will be powered by a 3.7 V battery. I need to use battery as long as possible. So I decided to make peripheral...
When I put the device into sleep it draws app 30 uA in sleep mode. Read in the manual: "Core standby current= 50 μA", "Current drawn if HFXO is forced on through for instance...
Hi,
I am trying to emulate a vendor's tool, whose BLE properties are configured as follows: Custom 128 bit Service UUID like XXXXXXXX- 0000 -XXXX-XXXX-XXXXXXXXXXXX
Custom...
hi, I am working nrf52832. I am making configuration file for nrf52.so I want to used Led3 set as high.
#define LED3 ((GPIO_PIN_CNF_SENSE_High << GPIO_PIN_CNF_SENSE_Pos...
Hi, I am looking to access nRF9160 modem via I2C. Essentially looking for hooks/ serial interface hand-off points used for instance in AT Client sample or Serial LTE Modem...
We have some devices out in the field with a mixture of application versions. In one particular case, we have device A on application version 10 and we have device B on application...
Hi there
I am having issues to perform disconnections from my central device when calling sd_ble_gap_disconnect()
most of the time I am able to disconnect properly using...
Hi Devzone:
I am researching how to maximize radio performance and stumbled on a statement on page 356 in the spec:
"Typical sensitivity applies when ADDR0 is used for...
Hi! Currently I have a nrf52840 devkit hooked up to an SD-card for storage through FATFS (using SPI). I would like to add a BME680 environment-sensor to the board and have...
