I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
In the documentation , it is stated:
The SAADC is preceded by a gain stage which has a programmable gain. The voltage range seen at the input of the gain stage is:
...
Hi everyone! I'm having difficulties in setting up a little project in which I want to pass I2S data over USB. I know I'm using the old USB Audio Class endpoints, but everything...
Hi Nordic Team,
Does the reset of 54L15 need to be handled? Still pull up a 1k resistor. Also, do I need two wires for debugging?
The customer has another question....
When transitioning from ncs v3.3.0 to ncs v3.4.1 noticed a warning about CONFIG_BOOT_ECDSA_CC310 being depreciated when building MCUboot. The release notes suggest using PSA...
I am using display example code from zephry repo. ( zephyr/samples/drivers/display at main · zephyrproject-rtos/zephyr ) . Connected to a nRF7002 dk , i am using EA W096016...
Hi,
We have a custom nRF5340 board with an nPM1300-QEAA-R7 (QFN32). On two assembled boards the PMIC behaves identically:
Power side works: it ACKs at 0x6B and the BUCKs...
We are currently working with a system that is using both and external flash and the HW WDG from the NRF5340.
Recently we are facing the issue, that we cannot re-flash the...
Hi Nordic Support,
We are using an nRF54LM20 DK, PCA10184 hardware revision 0.7.0, for automated side-channel analysis (SCA) testing.
Our requirement is to repeatedly...
Hi,
We are having issues with getting the output power of +23dBm when using the nRF9160 DK in CW mode.
We use the following command:
AT%XRFTEST=1,1,20,8470,23,1,4,0...
Hello,
I want to program and debug a custom board using my nRF52840 DK (PCA10056 v3.0.3) as the programmer, through the Debug out connector P19. Before I order the cable...
Hi,
We're moving a USB product from an FTDI bridge (FTDI's own VID/PID) to native USB on the
nRF52840, and need to settle its USB identity before release.
Setup...
I was running into issues with issuing the AT#XRESET command for a PPP/CMUX configuration. In an attempt to make the setup as robust as possible we found that the 9151 stopped...
Hi,
We are planning to use nRF Connect SDK Bare Metal (nrf-bm) v2.0.1 but would like to know which toolchain should be used alongside it?
https://nrfconnectdocs.nordicsemi...
