Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello everyone,
I am currently evaluating the nPM1300 Fuel Gauge with a LiFePo4 battery.
I would like to use nPM PowerUP to prepare the battery profile, but it appears...
hi support team,
i was testing mcumgr ota from uart, but found that the speed is slow how can i improve this?
i have change uart baud to 460800, but did not help. for...
Hi,
I'm using an nRF52840 DK to develop my prototype. Now I'm moving into the PCB design phase and I'm using a BLE ceramic antenna. I'll add a pi network footprint to tune...
I am using SPIS for my project. I am manually toggling CS for the peripheral. I get NRFX_SUCCESS for nrfx_spis_buffers_set() function. Also, when I probe the CS signal on...
Hi,
I am using the nrf52840 dongle board just to startup a project. I connected to the dongle a UART-USB converter to the dongle... but when I enable the UART into the firmware...
Hi Sir,
Please help to check do we support the ISO14064/ ISO14067 for the below part numbers.
1. Could you help to check do we pass the ISO14064/ISO14067?
If yes,...
I am implementing nrfx uarte on nRF52840 with ncs 2.6.1. I am using the example provided in modules\hal\nordic\nrfx\samples\src\nrfx_uarte as a reference.
Reason for using...
Windows 11, WSL2, NCS 2, VSCode
I want to be able to reboot my chip without the watchdog automatically being enabled on boot.
I cannot seem to disable it through the API...
Hello, the chip I am currently using is nrf52832 and the SDK version is SDK15.0. May I ask if all callbacks, interrupts, event handling, and main loops belong to the same...
Belows are that my development setup
sdk : sdk16
os : none
development tool : keil
To use the NRF7002, it is understood that the NRF CONNECT SDK must be used. However...
I have purchased two nRF52833 development kits and I would like to implement Direction Finding using AoA method. I have purchased the uBlox ANT-B10 patch antenna board for...
Hello,
I'm a relative neophyte when it comes to non-hardware aspects of WiFi ICs, so I have some basic questions about the nRF7002; these are features my client is asking...
Hello!
I am new to the nRF52840 Dongle and Kali Linux running on a Pi 4B. Can someone point me to a source to walk a newbie through the install process? Any help is greatly...
