I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Can the nPM1300 be used without any charging support (no battery, no fuel gauge)?
I know this is an unusual arrangement but we have a requirement that a separate device...
I'm having 52840-DK boards 3 and installed vscode,nrfsdk v2.2.0 and v2.8.0. i want to explore how to use FOTA for zigbee. are there any sample available to make it work and...
Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Similar issue to Attempted to change incrementally the Voltage for VDDIO and VDD_DBGR, however, this didn't change the state of the LEDs. Successfully compiled and flashed...
Hi,
We are seeing weird behavior in the way the nRF Cloud UI displays changes in the device shadow, specifically for properties that are being nulled-out.
Let's say we...
Hi,
Im using an SPI device and also the SPIM NRF driver. This device is not always on, but the overall flow is:
Power On the device on boot and do basic info readings...
I have ordered two boards using the nrf52840
I was able to flash the first board and my firmware is working as expected however whenever I try to program the other one I...
When uploading a network core image though MCUBoot and confirming the image, sometimes it fails to accept and on other builds it accepts the update.
I have narrowed this...
Hi
Greetings, Hope you are doing well.
I am fairly new to using the nRF Connect SDK through VS Code. I completed the nRF Connect SDK Fundamentals course, and I also noticed...
Hi All,
I am currently working on an project with the nRF9151 using the nRF SDK v3.1.1 and MCUboot and I need to sign my application images using an external HSM. I am using...
I am having this problem in my Macbook Air M4. It times out when flashing the application via nRF Connect SDK extension. I also tried to run the nrfjprog command myself and...
I’m evaluating the nRF Connect SDK Bare Metal SDK and hit an issue with the bm_storage library. bm_storage_write() and bm_storage_read() work correctly, but bm_storage_erase...
When using GNSS periodic mode with nrf_modem_gnss_fix_interval_set() set to 20 minutes and nrf_modem_gnss_fix_retry_set() to 5 minutes, the actual wake-up intervals are inconsistent...
Hi,
I have a feeling we may be experiencing Modem Reset Loop Restrictions on some of our devices, so I want to put in something to our application code so we know and can...
Hi ,
I need to do create the bootloader . generally what we dump in to the board was the firmware not bootloader right. I want to do the OTA updates on the nRF52840 Dev...
