Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hi all!
I'm currently working on the UART on the nRF5340 board. The SDK describes three options: -polling API,
-interrupt-driven API,
-asynchronous API. With Polling and Asynchronous...
During development I noticed the following behavior:
If NRF_SDH_BLE_GAP_DATA_LENGTH=251 and NRF_SDH_BLE_GATT_MAX_MTU_SIZE=185, on Android devices the connection procedure...
Hi
For some reasons my Windows 10 laptop reports two JLink CDC UART Ports when I connect one of my nRF52SDK boards.My plan is to use this board with nrf Sniffer / Wirshark...
Im struggling here with porting my code from SDK15 to NCS 2.0.2
Im happily TXing data from NRF52811 via UARTE and receiving via FTDI to PC, but Im unable to receive any...
Hello,
in the nrf connect application for mobile phone I can see the RSSI values being updated when scanning, but when I connect to my peripheral the RSSI info is not available...
Hello, I'm developing firmware for our custom board with a nRF9160.
The problem I'm having is that the modem crashes with error code 0x10 sometimes (read: about every 3rd...
HI guys I am working on nrf connect sdk v2.0.0, I am trying to modify periodic_adv example to stop changing mac address every time an advertising restart.
Hi,
I am writing the sample program "https_client" to the nRF9160-DK with Visual Studio Code's "Flash". I need to set the APN every time I write with Flash. Is it possible...
Hi,
When I'm trying to use LVGL along with Zephyr, I get the following:
I already tried to "play" with different CONFIG_MAIN_STACK_SIZE and CONFIG_IDLE_STACK_SIZE...
Hello Team Nordic,
We are using nrf9160 DK with nrf connect SDK 2.0.0 and mfw_nrf9160_1.3.2 modem firmware . In the Download_Client example we have changed the URL and the...
Based on the reference designs, the nRF52832 needs a 100pF decoupling capacitor on the DEC3 input. From my reading, this is a PSU decoupling capacitor, presumably for higher...
Our devices are provisioned via mesh shell, not over the air so we have to pass the IV index to the mesh provisioning command However, because the current IV index is not...
I was asked to create a windows application to get the device name and the signal strength of nearby modules with a nrf ble module.
The idea is to have an application the...
Hi,
I'd like to have a HW review. I have designed a PCB around the FSC-BT630 module which includes the nRF52832.
I have included all the files necessary for your to check...
