Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I tried the tutorial at link below
h ttps://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kiti in conjunction with nRF5_SDK_17.1.0
devzone.nordicsemi...
Hi,
I have a NRF52840 and a bluetooth device. Is there a way to automate the communication by writing/reading the HEX code. It is essential for product testing. Example...
Hi
I am using FOTA DOWNLOAD to update device's application firmware. https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrf/libraries/networking/fota_download.html...
my net core only output the boot information and i enable config_log that uart console will put some strange info
CONFIG_LOG_DEFAULT_LEVEL=3
appcore output to ttyACM1...
Hi
I could not really find a satisfactory answer to my question, what (if any) impact has the setting of the SLEEPDEEEP bit before calling nrf_pwr_mgmt_run? I'm wondering...
How does the slm routine of ncs1.9.1 use rtt log. Below is my configuration:
With the default configuration, there should be RTT log output, but nothing happens in the...
Dear Nordic Engineers
If we use the NFC Tag of nRF52 series chip.A re there any card readers on the market that can read or write?
Such as ， NXP's NFC tag chip can be...
Hi Nordic,
I am using nRf52833-DK with zephry, an now I'm tring to drive ws2812 led strip.
I notice that there is no nRf52833-DK example in zephyr/samples/drivers/led_ws2812...
Hello,
At the following URL,
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multiprotocol_support.html
In "The Thread and Zigbee protocols support...
Good Morning people. I'm developing a module with the soic nrf52832 and I'm having doubts about the electrical schematic of the UART communication with another MCU. I analyzed...
Hi
In the old SDK I was able to put manufacturing data into the scan response package using:
ble_advertising_init_t init; ble_advdata_manuf_data_t manuf_data;
and just...
I am migrating to ESB from Gazell to take advantage of the static 252 byte sized payloads. However, there are two things that are very different that I would like to figure...
Hello all,
looking at how to navigate with the nRF tools, hardware amd software.
For example, have designed a bit of applciation with seome peripheral drivers, but I am...
