I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
We evaluated the BLE Mesh DFU performance on the nRF52840 and observed that transferring a 342 KB binary took approximately 36 minutes. This aligns closely with the documentation...
Hello!
Can you map the zephyr versions to the LTS versions if possible?
We are using NCS 3.02 with the zephyr version 4.0.99. How does this relate to any of the LTS...
Hello.
I am developing in the following environment. ・nrf52832 custom board ・nRF5 SDK v17.1.0
This program already supports BLE communication, BLE DFU functionality, AD...
Hello.
During production, we occasionally encounter products that exceed the reception sensitivity standards.
Of course, we only select those that completely exceed...
I need to use PPI on my custom nRF52840 board, which selects soc nRF52840 as per copying nrf52840dk. However, this doesn't enable "HAS_NRFX", which is hard to track how that...
Hi,
I'm running the location sample on nrf9151dk from v3.0.0 of nrf-sdk. Hardware details:
I have these additional configs added to my prj.conf
This is the output...
I am working on a custom Cluster Definition Using Matter Cluster Editor 0.1.0 I have created a couple of structures on the structure tab and they are not being saved to the...
I am designing a wearable device that uses BLE and UART. During the development stage, I worked with the nRF52 Development Kit and started with the ble_app_uart example from...
Hi,
What would be the best way to alter pin's functionality from UART TX ->RX->GPOUT ->GPIN in runtime? (NCS2.5/Zephyr nRF52840)
Is it supported by Zephyr/devicetree...
Hi. I can't build the hello_dect example using cmake, the build process is failed with the following error: In file included from /home/cybermag/ncs/nrf/modules/trusted-firmware...
Hi,
In this post Hung Bui states that there can only be "maximum 4 pin events, each for one GPIO pin (so max 4 pins at a time)". This is (apperently) not true since I...
While scanning for devices with NCS 2.9.2 my device suddenly stops sending adv reports after a few hours.
It seems like this might have been fixed in a recent version...
BOARD: nrf54l15 DK
SDK: 3.1.0
Hi,
I am trying to setup my low power preipheral with a new ble address via bt_id_create.
Everthing works fine when I use the exact...
Hello! I am developing an application for the nRF5340, and I am using split cores, so the controller is on the network core and the application is on the other core. I want...
