I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Dear Members,
We have 2 ANT receivers and 1 ANT Speed Transmitter, (Bicycle Speed Cadence) , Garmin GSC-10,
Is it possible ? Looks like one receiver gets a good value...
Hi,
I am using NCS v2.0.0, VScode with "nrf connect for vscode v2022.7.242".
I can't build any samples with MCUboot, by enable CONFIG_BOOTLOADER_MCUBOOT =y.
The build...
The following error occurs when I plug in the USB cable to burn the firmware，This is an interesting bug: it usually fails on the first burn, but succeeds on the second or...
Hi everyone,
I am new to nRF52833, and trying to learn it with some tutorials. I am following this tutorial.
You can download my "examples" file from here . You should...
Hi,
Can you please provide some sample code for sending data to Tm4C using ble_app_uart in VScode and also tell me which function I need to use for sending some data from...
When I use Windows nRF Connect to connect to nRF52832 device. It pop up window for user to enter passkey. But When I use iOS nRF Connect to connect to nRF52832 device. It...
HI, I am start use NRF52840DK(rev3) to devlopment usb application，but jlink always show this information
I try to use 'nrfjprog --recover' to disable read protection,...
Hello Groups,
I'm trying to send I2C/twi data from nRF52832 using the Nordic development board with nRF Connect SDK 1.9.1.
Based on the sample project ble_app_uart, I...
Hi nordic:
As shown in the figure below, I see that the BLE protocol standard mentions the ScanReq backoff mechanism. Does NORDIC implement it?
jermi.jin
thanks!!...
Hi,
The central_uart sample hardfaults when bt_enable(NULL) is entered. I can use the debugger and step over the first couple lines but stepping over bt_enable causes a...
Hi
I have integrated the example code for mesh dfu provided in the nrf mesh sdk5 in my main application . I have followed all the steps mentioned in this dfu guide. The...
Hi,
We have a working LwM2M device based on nRF9160 and NRF Connect SDK 1.1. When we run with a short register-update period (30 seconds) on a NB-IoT network it works. When...
Good Morning,
I would like disable passkey in the example "peripherals_hids_keyboard". I am able to connect with differents hosts (2 smarts and i computer) but I'm having...
On SoftDevice S140(V7.2.0)
ble_gap_adv_report_type_t status has four types.
BLE_GAP_ADV_DATA_STATUS_COMPLETE BLE_GAP_ADV_DATA_STATUS_INCOMPLETE_MORE_DATA BLE_GAP_ADV_DATA_STATUS_INCOMPLETE_TRUNCATED...
