I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am testing nRF5_SDK_17.1 examples/dfu/secure_bootloader/pca10040_uart_debug
After I run on SES. I got this memory map. It overlaps softdevice area.
With armgcc ...
How do I use printf to output my own messages, and read incoming data, from a UART port that is separate from Zephyr's debugging outputs? This UART line will be connected...
Hello, we are trying to get software running on our custom board.
Last week we tried to test the software written on a development kit of the NRF9160 on to our custom board...
Hi.
I'm trying to add a SPM partition to my project. Like another project i did in the past, i followed this guide: https://devzone.nordicsemi.com/guides/nrf-connect-sdk...
We would like to know there is any direct test mode for TX power of NRF21540DK.
We only found the method of nRF52833 direct test(TX). But we can find how to do with NRF21540DK...
Hi,
I wonder how to use the internal capacitor of the nrf5340.
The nRF5340-DK operates at 32M=8pf 32.768k=9pf without any special settings.
If i use 10pf products for...
Hi,
I'm porting firmware between nRF52 and nRF53 platforms. What is the equivalent of NRF_UICR-> CUSTOMER on nRF53 to keep data like serial number etc.
Thanks
Sebas...
We are developing a custom device based on the nRF9160 SiP Revision 2 with multiple connections over LTE-M and we are experiencing problems with keeping our only TCP connection...
Hello, I'm using nrf mesh serial example in nrf5sdkformeshv500src, in the serial node i subscripted to 0xC000 but i can't not received messages more than 32 node, my netwwork...
Hi All,
Sorry to ask this question, I just learned a little about cmake.
Now I wanted to add a few src files based on the light switch example in SES. Do I have to create...
Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hi.
I am trying to update my Softdevice using DFU.
If I update from S112 to S140, do I have to upload the application as an image built with S140 as well?
And do I need...
Hi there,
I can't seem to add header files to my project.
The header files underlined in red are not from the Nordic SDK installed from the Toolchain Manager.
...
Hello,
we are currently developing an MQTT Bridge Application. We plan to use a nrf52840 in combination with the nrf9160 as our Bridge which is going to send its data...
Hi,
I working with NRF52840 DK board, I need to read some potentiometer values or any sensor values and also send me the example code ADC with Bluetooth. I need to transfer...
