Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I have a product running on an nrf5340 and part of it is running a nordic sample project. In the sample project there is a call to `k_msgq_get()`. The program spends a lot...
Hi
I'm evaluating the nrf5340dk devboard and are building a simple application on top of zephyr. I'm using Cmake and ninja on Ubuntu. The code builds and I'm able to flash...
Hi there,
We are currently doing some testing around the low power modes of the nrf5340. Detailed info on the Low Power mode and Constant Latency mode is a bit hard to find...
I'm trying to get my nrf9160dk board up and running with the nrfcloud service. However, when I input the SIM ICCID and PUK, the nrfcloud site starts it's "working" process...
Good day
After flashing a sample to my thingy 91 I seem to have lost the Jlink connection. All im picking up is the UART via nRF connect Programmer. Is there a Bin file...
Hello Sir/Mam;
I am new in nordic environment so i need your valuable guidance . i want to read a sensor data using Uart . I have successfully do same thing on Arduino board...
Hi,
I had previously asked about SPI interfacing of the RFID card reader and I was successful in creating a custom application using connect SDK 1.5.1.
But according to...
I currently have an application with B0->SPM->MCUBOOT->APP and am looking for an example of how to upgrade MCUBOOT itself over the air from a file downloaded from some server...
We're using a nRF52DK and the Nordic-Programmer-App to flash our firmware on our custom boards. After upgrading to Programmer v2.3.3 I'm getting the Error-Message "Part of...
Hi,
I am able to successfully build and flash applications from the CLI.
When setting up the nRF Connect VS Code extension, I run into an issue where it can't seem to...
Hello, I am trying to use the spi_flash sample project with a laird bl654 dvk. When I run the project however, dev->state->init_res = 19 and will not run for me. It recognizes...
Hi,
I have been trying for several days to modify the ble_app_uart project on the peripheral side to use the BLE Long Range, unsuccessfully. I use the NRF52833-DK with...
Hello, sir.
I want to use the i2c bit bagging method, thus I used the DeviceDownloadnRF5 SDK 17.1.0 ddde560nRF5 SDK 17.1.0 ddde560componentsdrivers nRF5 SDK 17.1.0 ddde560componentsdrivers...
I want to use the Zephyr Shell with my own transport layer. Since the only connection I will have to the modem is over SPI, I want to have the SPI read/writes handled with...
